Chef-o-Matic KITCHEN ROBOT Manual De Instrucciones página 9

solid ingredients.
The programme cooks food at 100o C.
For the last 1.5 minutes, blend the mixture on spe-
ed 4 for 30 seconds and on speed 10 for the last
minute.
The default setting is 35 minutes, 100 degrees Cel-
sius, speed 1.
The programme does not allow temperature (100o
C) or speed (1) to be modified.
The time can be adjusted from 25 to 45 minutes.
SAUCE:
For preparing delicious sauces.
The programme defaults to 10 minutes, 85 de-
grees Celsius.
You can change the speed from 1 to 4.
You can change the temperature from 60 to 105
degrees Celsius.
You can change the time from 1 to 60 minutes
STEAM:
For steaming food.
Fill the mixing jar with at least 500 ml of water.
Remove the measuring cup/plug to leave the lid
nozzle open and place the steamer on top with the
ingredients.
The programme does not allow changing the spe-
ed (it will be 0).
The temperature can be changed from 100 to 120 ºC.
The time can be set from 5 to 60 minutes.
PASTRY:
For making delicious doughs, cakes and biscuits.
Generally, it is advisable to use the blade guard
when using this programme.
The programme kneads at different speeds and
times. In any of the selected options, it kneads the
product for 6 seconds, stops for 3 seconds more
and starts kneading again, which results in uniform,
well-developed doughs.
It does not allow temperature selection.
The kneading speed can be changed from 2 to 4:
For speed 2, the maximum time is 12 minutes.
For speed 3, the maximum time is 3 minutes.
For speed 4, the maximum time is 2.5 minutes.
5. ASSEMBLY OF THE MIXING JAR:
SEALING GASKET OF THE JAR:
The lid of the jar has a sealing gasket that prevents
liquid from escaping when the food processor is
processing food.
Make sure that it is securely attached to the lid be-
fore using the appliance.
Cooking hot ingredients can create a vacuum in the
beaker, which can cause the sealing gasket to be-
come stuck in the beaker when the lid is removed.
In this case, wait for the preparation to cool before
removing the gasket.
How to install the sealing gasket under the mixing
jar lid:
Graph 6
BLADE:
Remove the blade:
The blade must be removed in order to clean the
mixing jar properly.
Hold the upper part of the blade with one hand and
place the key in the lower part of the socket with
the other hand.
Turn the key counterclockwise to remove the blade
from the socket.
How to remove the blade:
Graph 7
To fit the blade:
Place the sealing gasket under the blade.
Place the blade in the mixing jar and hold the upper
part of the blade with one hand. Place the key in
the lower part of the socket with the other hand.
Turn the key clockwise to adjust the socket blade.
How to fit the blade:
Graph 8
Caution:
The blade is very sharp. Please use it with care!
Hold only the upper part of the blade!
The sealing ring must be securely attached to the
blades. If food is cooked or chopped without the
sealing ring in place, the beaker may leak from
underneath and the main unit may be damaged.
ASSEMBLE THE MIXING JAR:
Graph 9
1- Place the lid on the mixing jar. Press the lid with
both hands and, at the same time, turn it clockwise.
You will then hear a "click", which means that the lid
is correctly installed.
2- Insert the jar into its housing. Make sure that the
Z1 mark points to the Z2 mark. At this point you will
also hear a "click", which means that the bowl is
correctly positioned.
3- Insert the measuring cup/plug into the jar lid (see
figure above).
DISMANTLE THE MIXING JAR:
Figure 10
1- Remove the mixing jar from the main appliance.
The jar can be easily removed.
2- Be careful if you have cooked with a temperatu-
re programme. The jar may be hot.
SHARPEN THE BLADES:
You will probably never need to sharpen the blades
of your machine.
9