Publicidad
Idiomas disponibles
Idiomas disponibles
DETAILED SAFETY REGULATIONS:
• Before connecting the vacuum cleaner to the mains, always check
that the mains voltage corresponds to the voltage specified on the
rating plate of the device.
• Do not use in a potentially flammable or explosive atmosphere.
• Inspection and maintenance must be performed with the device
turned off and disconnected from the power source.
• When using motorized suction nozzles:
−do not use for water suction.
−do not immerse in water for cleaning
−Do not use tips if you find them damaged - check their technical
condition regularly.
• Inspection and maintenance should be performed after the
electrically driven suction nozzle has been removed.
• Note: the hose can become static.
• Do not step on or pull on the hose. A damaged hose should be
replaced before further work.
• Keep the squeegee at a safe distance while working.
• Do not allow the power cord to come into contact with water, oil or
other liquids.
• Do not immerse the device in water, do not touch it with wet hands,
do not use water for cleaning in order to avoid electric shock.
• Do not suction hair, glass, metal, sharp or sticky parts. This will clog
or damage parts of the device.
• It is forbidden to suck in flammable, hot, glowing or corrosive
elements, cigarette butts, matches, etc. - it may result in fire or
electric shock.
• The device is not adapted and not suitable for extracting harmful
dust.
• Do not use when the air inlet is blocked or the bag is clogged, as
this may damage the device.
• When the device is not in use, remove the plug from the socket.
• Regularly check the technical condition of the device. Replace
damaged or worn parts.
• Do not use the device if the cord is damaged. Do not touch the
cable before disconnecting the power supply!
• If you find any damage or notice any disturbing signals, such as
excessive temperature and noise, turn off the device immediately
and disconnect it from the power supply.
• Protect against rain.
• Use only spare parts recommended by the manufacturer
• All repairs should be carried out at an authorized service center.
Explanation of the pictograms used
1
2
1. Attention! Take special precautions.
2. Read the operating manual, observe the warnings and safety
conditions contained in it.
3. Use personal protective equipment (safety goggles, hearing protection,
dust masks)
4. Disconnect the power cord before starting maintenance or repair work.
5. Protect against moisture.
6. Use appropriate attachments for extracting water.
CONTENTS
• Package x 1
• Snake x 1
• Vacuum cleaner x 1
• User manual x 1
• Tube x 1
• Wheels x 2
• Dust Filter x 1
• Sponge Filter x 1
• Bags x 2
• Connector x 1
• Hose reduction x 1
• Suction cups x 5
APPLICATION
A universal vacuum cleaner designed for dry and wet operation with the
assistance of electric and pneumatic tools.
DESCRIPTION OF THE GRAPHIC SIDES
Figure A:
1. Suction cup
2. Telescopic tube
3. Connector
3
4
5
4. Snake
5. Top inlet
6. Vacuum cleaner handle
7. Switch
8. Front inlet
9. Handle
10. Wire
11. Clasps
12. Tank
TECHNICAL PARAMETERS
Supply voltage
Power frequency
Engine rated power
Height
Total capacity of the tank
Length of the suction hose
The diameter of the end of the suction hose
Suction power
Protection class
Level of security
Mass
Year of production
59G610 stands for both the type and designation of the machine
NOISE AND VIBRATION DATA
Sound pressure level
Sound power level
Information on noise and vibration
The level of noise emitted by the device is described by: the level of the
emitted sound pressure Lp
the measurement uncertainty).
The following information: emitted sound pressure level Lp
level Lw
were measured in accordance with Directive 2000/14 / EC.
A
SWITCHING ON AND OFF
Connect the plug to the socket. To turn on the vacuum cleaner, slide the
switch to position 1. Move the button to position 0 to turn off the vacuum
cleaner (Fig. B) .
HOSE CONNECTION TO VACUUM CLEANER
Put the beginning of the hose over the hole and screw it clockwise until it
stops. Unscrew to disconnect (fig C) . The vacuum cleaner has 2 hose
entries. The entrance at the top is designed for dry operation, while the
entrance for wet operation is at the front, at the bottom of the vacuum
6
cleaner. Close the unused inlet.
Note: for wet operation, remove the dust filter and bag and use a sponge
filter.
CONNECTING THE HOSE TO THE PIPE
A tube can be connected to the handle of the hose for extension. The pipe
is connected to the handle, then you have to twist it clockwise to screw it
on (fig. D) .
CONNECTING THE SUCTION CUP
The suction nozzle is connected to the pipe by tightening it
clockwise. Unscrew to disengage (fig E) .
FITTING THE FRONT CASTERS
The front wheels are mounted according to Fig. F . The water reservoir
should be empty.
CABLE HANGER
The vacuum cleaner is equipped with a hanger for hanging the cord. When
the vacuum cleaner is not in use, wind the cord around the hanger to
protect it from damage (fig. G) .
STORING YOUR ACCESSORIES
There are openings on both sides of the device for accessories (suction
nozzles) (fig. H) .
BLOWER FUNCTION
The vacuum cleaner can be used as a blower. To do this, connect the
hose to the blower opening (fig. I) .
FILTER BLOWING
The suction power can be increased by blowing through the filter. To do
this, while working, place the end of the hose in the appropriate socket on
the upper part of the device (fig. J) .
BAG ASSEMBLY AND REPLACEMENT
6
59G610 industrial vacuum cleaner
Parameter
Lp
= 97.0 dB (A) K = 1.2 dB (A)
A
≤70dB (A) K = 1.0 dB (A)
Lw
A
and the sound power level Lw
A
USE
Value
230 V AC
50 Hz
1600 W.
51 cm
30 l
4 m
Ø59 / Ø54 mm
170W
II
IP X4
12.5 kg
2022
(where K is
A
, sound power
A
Publicidad
