EINHELL TE-AD 18 Li Manual De Instrucciones Original página 16

6. Operation
6.1 Charging the LI battery pack (Fig. 2-3)
1. Remove the battery pack (6) from the handle,
pressing the pushlock buttons (a) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(7) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 "Charger indicator" you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to become charged, ple-
ase check
•
whether there is voltage at the socket-outlet
•
whether there is proper contact at the char-
ging contacts on the charger.
If the battery still fails to become charged, please
return
•
the charger
•
the battery pack
to our Customer Service Department.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
6.2 Turning the drill head (Fig. 4)
The cordless angle drill features a swiveling drill
head that enables you to fasten the drill head in
four diff erent positions (Fig. 4).
To swivel the drill head, press and hold the re-
lease button (4). You can then swivel the drill head
into the required position.
Anl_TE_AD_18_Li_SPK13.indb 16 Anl_TE_AD_18_Li_SPK13.indb 16
GB
6.3 Forward/Reverse switch (Fig. 5/Item 2)
With the slide switch above the On/Off switch you
can select the direction of rotation of the battery-
powered drill/screwdriver and secure it against
being switched on accidentally. You can choose
between clockwise and anticlockwise rotation. To
avoid causing damage to the gearing it is advisa-
ble to change the direction of rotation only when
the tool is at a standstill. The On/Off switch is blo-
cked when the slide switch is in centre position.
6.4 On/Off switch (Fig. 5/Item 3)
Infi nitely variable speed control is possible with
the On/Off switch. The further you push the
switch, the higher the speed of the cordless angle
drill.
6.5 Battery capacity indicator (Fig. 6 – Item c)
Press the battery capacity indicator switch (b).
The battery capacity indicator (c) shows the char-
ge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6.6 LED lamp (Fig. 5/Item 5)
The LED lamp (5) can be used in poor lighting
conditions to illuminate the area where you want
to drill or screw. The LED lamp (5) will be lit au-
tomatically as soon as you press the ON/OFF
switch (3).
6.7 Changing the tool (Fig. 7)
Important. Set the changeover switch (2) to its
centre position whenever you carry out any work
(for example changing the tool, maintenance
work, etc.) on the cordless screwdriver.
•
The cordless screwdriver is fitted with a
quick-action chuck (1) with an automatic
spindle stop.
- 16 -
16.08.2023 12:49:38 16.08.2023 12:49:38