Publicidad
Idiomas disponibles
Idiomas disponibles
d)
Do not abuse
the cord.
Never use the cord
for carrying,
pulling
or unplugging
the power
tool.
Keep cord
away from
heat, oil, sharp
edges
or moving
parts.
Damaged
or entangled
cords increase
the risk of electric shock.
e) When
operating
a power
tool
outdoors,
use an extension
cord
suitable
for outdoor
use.
Use of a cord suitable
for outdoor use reduces
the risk of electric shock.
f) if operating
a power
tool in a damp
location
is unavoidable,
use a ground
fault circuit
interrupter
(GFCl) protected
supply.
Use of a GFCl reduces the risk of electric shock.
3) PERSONAL
SAFETY
a) Stay alert, watch what you are doing and use common
sense when operating
a power tool. Do
not use a power tooJ while you are tired or under the influence
of drugs,
aJcohol or medication.
A moment of inattention while operating power tools may result in serious personal injury.
b) Use personal
protective
equipment.
Always
wear eye protection.
Protective
equipment
such as dust mask, nonskid
safety shoes,
hard hat, or hearing
protection
used for appropriate
conditions
will reduce personal
injuries.
c) Prevent
unintentional
starting.
Ensure
the switch
is in the off position
before
connecting
to
power source
and/or
battery
pack, picking
up or carrying
the tool. Carrying
power tools with
your finger on the switch or energizing
power tools that have the switch on invites accidents.
d) Remove
any adjusting
key or wrench
before
turning
the power
tool on= A wrench
or a key
left attached
to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach.
Keep proper footing
and balance
at all times.
This enables
better control
of the power
tool in unexpected
situations.
f} Dress property.
Do not wear toose cJothing or jeweJry. Keep your hair, cJothing and g!ovee away
from moving
parts. Loose clothes, jewelry or long hair can be caught in moving parts.
g) If devices are provided
for the connection
of dust extraction
and collection
facilities,
ensure these
are connected
and properly
used. Use of dust collection can reduce dust-related hazards.
4) POWER
TOOL
USE AND CARE
a) Do not force
the power
tool.
Use the correct
power
tool for your
application.
The correct
power
tool wifl do the job better and safer at the rate for which it was designed.
b) Do not use the power
tool if the switch
does
not turn
it on and off. Anypower
tool that
cannot be controlled
with the switch
is dangerous
and must be repaired.
c) Disconnect
the plug from
the power source
and/or
the battery
pack from
the power tool
before
making
any adjustments,
changing
accessories,
or storing
power
tools.
Such
preventive
safety measures
reduce
the risk of starting
the power tool accidentally.
d) Store idle power
tools
out of the reach
of children
and do not allow
persons
unfamiliar
with
the power tool or these
instructions
to operate
the power tool.
Power tools are
dangerous
in the hands of untrained
users.
e) blaintain
power tools. Check for misalignment
or binding
of moving
parts, breakage of parts and
any other condition
that may affect the power tool's
operation.
If damaged,
have the power tool
repaired before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting
tools
sharp
and clean.
Properly
maintained
cutting
tools with sharp
cutting
edges are less likely to bind and are easier to control
g} Use the power tool, accessories
and tool bits, etc. in accordance
with these instructions,
taking
into account
the working
conditions
and the work to be performed.
Use of the power tool
for operations different from those intended could result in a hazardous situation.
5) BATTERY
TOOL
USE AND CARE
a) Recharge
only with the charger
specified
by the manufacturer.
A charger that is suitable for
one type of battery pack may create a risk of fire when used with another battery pack.
b) Use power
tools
only with
specifically
designated
battery
packs.
Use of any other battery
packs may create a risk of injury and fire.
c) When
battery
pack is not in use, keep it away from
other metal
objects
like paper clips,
coins,
keys,
nails,
screws,
or other small
metal
objects
that can make a connection
from
one terminal
to another.
Shorting
the battery
terminals
together may cause burns or a fire.
Publicidad
