Pentair FRESHPOINT F2000-B2B Instrucciones De Instalación página 5

INSTALLATION CONTINUED
A. Apply 3-5 wraps of plumber's tape to faucet stem.
INSTALLATION CONTINUED
B. Assemble faucet as shown in Figure 3.
C. Screw quick connector onto threaded end of faucet stem.
A. Apply 3-5 wraps of plumber's tape to faucet stem.
D. Place a mark 5/8" from one end of the blue tubing. Wet the end B. Assemble faucet as shown in Figure 3.
of the 3/8" tube and push into bottom of connector. The 5/8"
C. Screw quick connector onto threaded end of faucet stem.
mark should be flush with the collar of the connector.
D. Place a mark 5/8" from one end of the blue tubing. Wet the end
NOTE: To remove the tube, push on the fittings' collar and pull
of the 3/8" tube and push into bottom of connector. The 5/8"
the tube out.
mark should be flush with the collar of the connector.
NOTE: To remove the tube, push on the fittings' collar and pull
E. Holding the faucet, feed the tubing through the hole in the sink.
the tube out.
Position the faucet handle at a desired location.
E. Holding the faucet, feed the tubing through the hole in the sink.
F. Center the faucet and slip slotted disc between the bottom of
Position the faucet handle at a desired location.
the counter or sink and lock washer. Tighten the stem nut with
F. Center the faucet and slip slotted disc between the bottom of
a wrench until it is tight.
the counter or sink and lock washer. Tighten the stem nut with
G. Firmly insert spout into faucet base.
a wrench until it is tight.
4. Mounting the System
G. Firmly insert spout into faucet base.
A. Select a location under the sink, or other suitable area where 4. Mounting the System
the system will be installed.
A. Select a location under the sink, or other suitable area where
NOTE: The system carton can be used to determine the
the system will be installed.
operational footprint required for installation of the
NOTE: The system carton can be used to determine the
system and replacement cartridges. (Figure 4a)
operational footprint required for installation of the
system and replacement cartridges. (Figure 4a)
B. Mount the system vertically. Ensure mounting is level. Place
a pencil mark in the upper slots of the bracket mounting
B. Mount the system vertically. Ensure mounting is level. Place
a pencil mark in the upper slots of the bracket mounting
holes. (Figure 4b). Alternate mounting option: If mounting the
holes. (Figure 4b). Alternate mounting option: If mounting the
system near the floor, place the pencil marks above each of the
system near the floor, place the pencil marks above each of the
mounting holes on the bracket to ensure enough space resides
mounting holes on the bracket to ensure enough space resides
below the cartridge and the floor for cartridge replacement
below the cartridge and the floor for cartridge replacement
(Figure 4c). Use the 3/32" drill bit to create pilot holes for
(Figure 4c). Use the 3/32" drill bit to create pilot holes for
mounting.
mounting.
The system should be mounted to a firm, solid
The system should be mounted to a firm, solid
surface that is able to support the weight of the
surface that is able to support the weight of the
WARNING:
WARNING:
system.
system.
5. Connecting the Faucet to the System
5. Connecting the Faucet to the System
4b
4b
4c
4c
3
3
Faucet Stem
Chrome
Plate
Rubber
Washer
Slotted
Disk
Lock Washer
4a
4a
Filter 16.25" (413mm)
Filter
Filter
Filter
FRESHPOINT F2000-B2B, F2000-B2M Filtration Systems Instruction Manual • 5
FRESHPOINT F2000-B2B, F2000-B2M Filtration Systems Instruction Manual • 5
262.634.2386 | greatlakesintl.com
Faucet Stem
Chrome
Plate
Rubber
Washer
Counter Top
Slotted
Disk
Counter Top
Lock Washer
Stem Nut
Stem Nut
Quick
Connector
Quick
3/8" Tubing
Connector
3/8" Tubing
7" (178 mm)
7" (178 mm)
Inlet
Inlet
16.25" (413mm)
10.75" (273 mm)
10.75" (273 mm)
Outlet
Outlet