Publicidad
Idiomas disponibles
Idiomas disponibles
1. Tidy cables and loose items from the
ground and move any unstable, fragile,
precious, or dangerous items to prevent
personal injury or property damage due to
items becoming tangled in, struck by, or
knocked over by the robot.
2. When using the robot in a raised area,
always use a secure physical barrier to
prevent accidental falls that may result in
personal injury or property damage.
Note:
When using the robot for the first time, follow
it throughout its whole cleaning route and watch for
potential problems. The robot will be able to clean by
itself in future uses.
Place the Dock
B1
Keep the dock on a level surface, flat against
a wall. Connect it to a power supply.
B1-1—More than 0.5m (1.6ft)
B1-2—More than 1.5m (4.9ft)
Notes:
• Allow more than 0.5 m (1.6 ft) of clearance on each side,
and 1.5 m (4.9 ft) in front of the dock.
• If the power cable hangs vertical to the ground, it may
be caught by the robot, causing the dock to be moved
or disconnected.
• The dock indicator is on when the dock is powered on,
and off when the robot is charging.
• Keep the dock away from direct sunlight or anything
that may block the dock location beacon; otherwise,
the robot may fail to return to the dock.
• To ensure a better user experience of the mobile app,
place the dock in an area with good WiFi coverage.
Secure the Dock
B2
Select a flat floor surface to place the dock
and wipe it with a dry cloth. Then, place the
dock on the selected surface against the
wall. Use the double-sided tape to secure
the dock better.
B2-1—Double-Sided Tape
Notes:
• Use of the double-sided tape to secure the charging
dock is optional.
• When necessary, remove the double-sided tape slowly
to reduce residue glue.
Secure the Moisture-Proof Mat
B3
After the dock is secured, use a dry cloth to
wipe the surface on which the moisture-
proof mat is to be placed. Tear off the
double-sided tape at the bottom of the
moisture-proof mat, and stick the mat on
the floor.
Notes:
• Alway place the moisture-proof mat on wooden floors.
• The moisture-proof mat attaches better to smooth
surfaces.
Powering on & Charging
B4
Press and hold the
button to power on the
robot. When the power light goes on, place
the robot on the dock to charge. Make sure
the charging dock power indicator turns off
and a "charging" voice alert sounds. To
maintain the performance of the
high-performance lithium-ion rechargeable
battery pack, keep the robot charged.
Note:
The robot may not turn on when the battery is
low. In this case, place the robot directly onto the dock
to charge.
07
Using the Mopping Module
B5
B5-1—Adjust the water flow
Slide the switch down to increase the water
flow and up to decrease the water flow.
B5-2—Fill the water tank
Remove the water tank stopper, fill it with
water, and close it.
B5-3—Install the mop cloth
Dampen the mop cloth and wring it until it
stops dripping. Insert it into the bottom along
the attachment slot and stick it firmly in place.
B5-4—Install the mopping module
Slide the mopping module along the back
of the robot as indicated by the arrow. A click
indicates that it is locked in place.
Notes:
• To prevent excessive dirt buildup during first-time use,
floors should be vacuumed at least three times before
mopping.
• If carpets are present, draw No-Go Zones or Invisible Wall
to prevent the robot going on them, or roll them up.
• To prevent corrosion or damage, only use the Roborock
branded floor cleaner in the water tank.
• Do not use hot water as this may cause the tank to deform.
• The mop cloth should be cleaned after 60 minutes of
mopping to ensure water flow and cleaning performance.
Remove the Mopping Module
B6
When the robot returns to the dock after
cleaning, press the latches on both sides,
and slide the mopping module backwards
to remove it.
Notes:
• Wash the mop cloth after each use, and regularly
Publicidad
