Cleaning And Maintaining - UFESA AS2205 Instrucciones De Uso

Ocultar thumbs Ver también para AS2205:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 1
- connect the tube (2) and the suction
hose (4) together. Figure2
- attach the brush (1), or whichever
accessory is required, to the vacuum
tube. Figure3
- holding the power cord by the plug,
pull out the required length and plug it
into the mains supply. Press the on/off
button (6). Figure4
- set the power with the power regulator
(7). Figure5
Suction intensity can also be regulated
from the hand grip. Opening the flap
(3) reduces suction, whereas closing it
increases suction. Figure6
- you can use the parking aid on the back
of the vacuum cleaner if you wish to stop
vacuuming for a short while. Slide the
catch in the brush into the groove at the
rear of the appliance. Figure7
- the wheels, the 360 swivel joint
and the carrying handle, along with its
compactness, make this vacuum cleaner
extremely mobile.
WHEN THE WORK IS FINISHED
When you have finished using the
appliance, set the power control (7) to
the minimum power position, press the
On/Off switch (6).
Press the automatic cable rewind pedal
(8) to wind the cable back in. Figure8
ACCESSORIES
Floor brush (1)
Figure 9
ACCESSORY NOZZLES
Crevice nozzle (15)
Use this accessory to vacuum crevices
and deep grooves and nooks, etc.
Upholstery nozzle (16)
This accessory has been designed to
clean all types of upholstery.
Furniture nozzle (17)
This accessory is ideal for vacuum cleaning
furniture and other delicate surfaces,
prevent surfaces from being damaged.
Brush for wooden flooring (18)
[Mod. AS2216]
This brush has been specially designed to
clean wooden floor surfaces. The soft hair
bristles brush over the surface picking up
the dust but without damaging the floor.

CLEANING AND MAINTAINING

CONTAINER FULL INDICATOR (13)
- When
suction
considerably and a red marker is moved
into a window mounted on the top of
the vacuum cleaner. This means that the
container is full or that the hose is blocked.
If this occurs empty the container (19)
- Press the release button (11) and
remove the container. Figure11
- Press button (24) to open the base flap
and empty the contents into a dustbin.
Figure12
- Cover the flap back up to close it again.
Place the container back into its housing
on the vacuum cleaner.
Cleaning the permanent HEPA filter
- Press the button (11) and take the
container (19) out of the housing.
- Turn the container lid (20) anti-clockwise
to remove it. Figure13
- Pull off the HEPA filter retainer (23)
and then the HEPA filter using the rib.
Figure14
Wash the HEPA filter and sponge with
water and mild detergent. Then leave
them to dry for at least 24 hours.
Once clean and dry, fit the HEPA retainer
(23) back into the container (19) and then
put the sponge and HEPA filter into the
retainer, fit the lid (20) into the container
by turning it clockwise until it locks into
position. Insert the fully assembled dust
container back into it housing on the
vacuum cleaner.
This vacuum cleaner has a missing filter
detection system which prevents the lid
from being put back on the container
when the HEPA filter is not fitted correctly.
Figure15
It is advisable to clean the HEPA filter at
least six uses.
The motor protection filter
The motor protection filter (14) should be
cleaned regularly by knocking out the dirt
and rinsing.
Press the button (11) to take the container
out of the housing, take the filter (14) out
and tapping it.
If it is very dirty, it should be rinsed. Figure
15
After cleaning, place it back, put the
container and lid in position.
power
decreases

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

As2216

Tabla de contenido