Descargar Imprimir esta página

cecotec CITY URBAN Manual De Instrucciones página 44

Bicicleta eléctrica

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 35
ENGLISH
4.
PAS (Pedal Assistance System): Pedal assistance: adjustable 0 ~ 5.
5.
Maximum speed MAX, average speed AVG
6.
Speed display area, (MP/H, KM/H).
Indicator lights
7.
a.
Low battery voltage
b.
Accelerator failure
c.
Brake failure
Controller failure
d.
e.
Motor failure
f.
Communication failure
8.
Cruising speed on
Pedestrian mode on
9.
Parameters
-
P01: Brightness, level 1 is the darkest and level 3 the brightest.
P02: mileage unit, 0: KM; 1: MILE.
-
-
P03: Voltage: 24 V, 36 V, 48 V, 60 V, 64 V; default 36 V.
-
P04: Latency time. 0 indicates no latency. Any other number indicates latency time. Range:
1-60 (minutes).
P06: Wheel diameter: inches. Precision: 0.1. This parameter is related to the speed displayed
-
on the console, so it must be entered correctly.
Note: The unit used is kilometres. When changing from kilometres to miles, the speed shown
will be in miles. However, the speed limit will not be changed to miles.
Note: Programmes P09-P15 are only valid in communication status.
P09: Zero (and non-zero) start. 0 indicates zero start; 1 indicates other non-zero starts.
-
-
P11: Pedal fl uidity range: 1-24.
-
P12: Gears: 0-5.
-
P14: The limit value of the controller is set to 12 A by default. Range: 1-20.
P15: Controller voltage setting.
-
-
P16: ODO. To set the value to zero, press and hold the button for fi ve seconds.
-
P17: Cruising speed. A value of 0 means that it is not allowed to activate the cruise speed.
When activated, 1 will be displayed.
P18: Adjusting the size of the speed on the display: 50 % ~ 150 %.
-
-
P19: 0 power bit, 0: 0, 1: does not include 0
-
P20:0:2 Protocol 1:5 S Protocol 2: Standby 3: Standby
Button operation. Fig. 8
The button operation is divided into: short presses, long presses, and long presses of combined
buttons.
86
CITY URBAN/ CITY URBAN PRO
-
Button to increase electrical assistance
-
Button to reduce electrical assistance
-
Power button
Short presses are used for frequent/rapid operations.
Control panel
To turn the display on/off , press and hold the
-
-
To turn the lights on/off press and hold down
-
To activate the start mode at standstill (6 km/h), press and hold down
To activate the start mode at standstill (6 km/h), press and hold down
-
To access the parameter setting menu, press and hold
accessed the setting parameters, press
accessed the setting parameters, press
-
To set the ODO to 0, press and hold
decrease each parameter, briefl y press
-
To show diff erent parameters on the display, press
To access the speed setting, press and hold
-
-
If no action has been done after 8 seconds, the changes will be saved automatically, and
the display will stop displaying the programmes.
5. CLEANING AND MAINTENANCE
-
It is recommended to use a damp cotton cloth or sponge instead of a hose or water jet.
-
It is recommended to clean the electric bike after each use. However, you can wash it
weekly. This will help to extend the lifespan of the electric bike.
Use soaps and care products for bicycles that do not attack plastics and seals, which can
-
be found in specialised shops. You can also use a soap solution or liquid detergent. Do not
use aggressive products or strong degreasing agents.
-
You can dry clean the electric bike with a cotton cloth or microfi bre cloth to prevent
corrosion.
-
The battery bracket is designed to allow water to drain off more quickly and the battery
contacts to dry easily. For this to happen, the bracket area and the plug must be kept
clean. The battery contacts are provided with a coating that protects the surface against
corrosion and wear.
Maintenance
Keep tyre pressure between 2.5 bar and 3.5 bar, maintain tyre pressure to avoid punctures. If
you notice any irregularities, take the electric bicycle to a mechanic.
Bike chain maintenance
-
Lubricate the chain regularly to avoid annoying chain noises and other problems when
ENGLISH
button.
.
.
and
. Once you have
briefl y to change parameters.
when in the parameter screen. To increase/
when in the parameter screen. To increase/
/
, respectively.
briefl y.
and
.
CITY URBAN/ CITY URBAN PRO
87

Publicidad

loading

Este manual también es adecuado para:

City urban pro0721507216