Publicidad
Idiomas disponibles
Idiomas disponibles
Pressure:
The performance level of the built-in hydraulic pump
can reach a short-term pressure level for a splitting
force of up to 4 tons. In the basic setting, hydraulic split-
ters are set at the factory to an approx. 10% lower out-
put level. For safety reasons, the basic settings must
not be changed by the user. Please note that external
circumstances such as operating and ambient temper-
ature, air pressure and moisture affect the viscosity of
the hydraulic oil. In addition, manufacturing tolerances
and maintenance errors can affect the reachable pres-
sure level.
8. Unpacking
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the pack-
aging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• In case of complaints the dealer must be informed
immediately. Subsequent complaints will not be ac-
cepted.
• If possible, store the packaging until the warranty
period has expired.
• Read the operating manual to make yourself familiar
with the device prior to using it.
• Only use original parts for accessories as well as for
wearing and spare parts. Spare parts are available
from your specialized dealer.
• Specify our part numbers as well as the type and
year of construction of the device in your orders.
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
9.
Attachment / Before starting
the equipment
At least two people are required to install the de-
vice.
9.1 Installing the handle (4) (enclosed accessories
bag a) (fig. 3)
Fasten the handle to the U-bar with two cylindrical
screws.
9.2 Installing the protective guard (L)
(enclosed accessories bag b) (fig. 4 + 5)
1.
Fit the protective guard (L) to the trunk guide plate
(5) and use the enclosed cylindrical screws and
nuts to affix it.
2.
Undo the cylindrical screw with washer that is lo-
cated on the wheel bracket.
3.
Fasten the other end of the strut to the protective
guard using the Phillips head screw and nut. (3)
4.
Now guide the open end of the strut (O) between
the washer and the wheel bracket, tighten the cy-
lindrical screw (4) again firmly.
9.3 Installing the tray table (K + M) (enclosed ac-
cessories bag c + d + e) (fig. 6 + 7 + 8)
1.
Attach the tray table (K) to the same side as the pro-
tective guard (L). Use two cylindrical screws and
spring washers to affix the table to the log splitter. (1)
Ensure that the table and the protective guard are
level in relation to each other.
2.
Undo the screw on the left of the foot.
3.
Fasten the other end of the strut to the protective
guard using the Phillips head screw and nut, align
everything and tighten the screws firmly.
4.
Now guide the open end of the strut (N) between
the screw and the foot bracket, tighten the screw
slightly.
5.
Repeat the process on the other side.
6.
Align both tables in relation to each other and use
the Phillips head screws and nuts (e) to affix them.
9.4 Installing the guard (E - J)
(enclosed accessories bag f) (fig. 9 + 10)
1.
Connect the guards (H) and (I) together, use two
Phillips head screws, clamping brackets and nuts
to affix it.
2.
Fasten the guards (H, I, J) to the holes provided for
this. These are on the side of the table and the pro-
tective guard. Fasten the guard with seven Phillips
head screws, clamping brackets and nuts. Fit the
protective guard (G) to the control lever protection
(11) and use a Phillips head screw and a nut to
affix it.
3.
Now fasten the guards (E + F) on the top. Fasten
them with eight Phillips head screws, clamping
brackets and nuts.
4.
Fasten the guards (E + F) together using two Phil-
lips head screws, clamping brackets and nuts.
www.scheppach.com
GB | 27
Publicidad
