Environmental Protection; Technical Specifications - Metabo KS 216 M Lasercut Instrucciones De Manejo

Ocultar thumbs Ver también para KS 216 M Lasercut:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

en
ENGLISH
 Check power cable and power cable plug or
battery pack for damage; if necessary have
damaged parts replaced by a qualified
electrician.
 Check all movable parts if they can be moved
freely across the entire range of movement.
Regularly, depending on conditions of use
 Check all screwed joints, retighten if necessary.
 Check reset function of the saw head (saw head
has to return to the upper starting position by
means of spring force), if required have spring
replaced.
 Slighly oil guide elements.
10. Tips and Tricks
– Use appropriate supports on the left and right of
the saw for long workpieces.
– Hold workpiece on the right of the saw blade for
suitable cuts.
– When cutting small pieces, use additional guide
(a suitable wooden board attached with screws
to the guide of the device, can be used as
additional guide).
– When cutting a curved (contorted) board (48)
place the convex side at the parallel guide/
ripping fence.
– Do not cut workpiece upright, but flat on the
turntable.
11. Accessories
Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
A Spray for maintenance and care for the
removal of resin residues and to preserve the
metal surfaces.
B Extraction adapter "Multi" for the connection of
extraction hoses with 44, 58 or 100 mm adapter
C Metabo all-purpose vacuum cleaner (see
catalogue)
D Stands:
Universal machine stand UMS
Mobile stand KSU 250 Mobile
Stand KSU 400
E Roller stand:
RS 420
RS 420 G
RS 420 W
For a complete range of accessories, see
www.metabo.com or the catalogue.
12. Repairs
DANGER
Repair of power tools must be carried out by
qualified electricians only!
When servicing use only identical replacement
parts.
If you have Metabo power tools that require
repairs, please contact your Metabo service
centre. For addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.

13. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of
disused machines, packaging and accessories.
14. Troubleshooting
Following you will find a description of problems
and faults that you may remedy yourself. If the
corrective measures described here do not help,
kindly refer to chapter 12. "Repairs".
WARNING
There are particularly many accidents in
connection with problems and faults. Therefore
keep in mind:
10
 Prior to each correction of faults, pull the mains
plug or remove the detachable battery pack
(27).
 Check that all safety devices are operational
again after each fault service.
No trimming function
Transport lock activated:
 pull out transport lock.
Safety lock activated:
 loosen safety lock.
Cutting power too low
Saw blade blunt (possibly tempering marks on
blade body);
Saw blade unsuitable for the material (see
chapter 11. "Accessories");
Saw blade contorted:
 Replace saw blade (see chapter 9.
"Maintenance").
Saw vibrates a lot
Saw blade contorted:
 Replace saw blade (see chapter 9.
"Maintenance").
Saw blade not installed properly:
 Install saw blade properly (see chapter 9.
"Maintenance").
Turntable hard to turn
Chips under turntable:
 remove chips.

15. Technical Specifications

Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
U
= mains voltage / voltage of battery pack
0911018691
I
= rated power
F
= min. fuse protection
P
= rated input power
1
0910058010
IP
= protection class
n
= no-load speed
0
v
= max. cutting speed
0
D
= saw blade diameter (outer)
d
= saw blade hole (inside)
6.3131700
b
= max. tooth width of the saw blade
6.3131800
A
= dimensions (lxwxh)
0910066110
m
= weight
Requirements for chip and dust extraction unit:
0910053353
D
= connection diameter of the extraction
1
0910053345
nozzle
0910053361
D
= minimum air throughput
2
D
= minimum negative pressure at extraction
3
nozzle
D
= minimum air speed at extraction nozzle
4
Maximum cross-section of workpiece, see table
on page 4.
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. Depending on the operating
conditions, the condition of the power tool or the
accessories, the actual load may be higher or
lower. For assessment purposes, please allow for
breaks and periods when the load is lower. Based
on the adjusted estimates, arrange protective
measures for the user e.g. organisational
measures.
Typical A-effective perceived sound levels:
L
= sound-pressure level
pA
L
= acoustic power level
WA
K
, K
= uncertainty
pA
WA
Wear ear protectors!

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ks 18 ltx 216

Tabla de contenido