Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
3.
Select direction of rotation
(triple beep, continuously repeated)
3.1
For reverse rotation
→
stick to full-throttle
position
OR:
For standard rotation*
→
stick to motor OFF
position
3.2
Stick to centre position
4.
Select motor cut-off type
(quadruple beep, continuously repeated)
4.1
For motor cut
(hard stop)
→
stick to full-
throttle position
OR:
For power
reduction *
→
stick to motor
OFF position
4.2
Stick to centre
position
5.
Select motor start-up behaviour
(five-times beep, continuously repeated)
5.1
For soft-start *
→ stick to full-throttle
position
OR:
For standard start-up
→ stick to motor OFF
position
5.2
Stick to centre position
6.
Select automatic timing
(six-times beep, continuously repeated)
6.1
For automatic timing ON*
→
stick in full-throttle
position
OR:
For automatic timing OFF
→
stick to motor OFF
position
6.2
Stick to centre position
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de
Operating Instructions
MULTIcont BL-15 brushless controller
⇒ Confirmation signal
emitted
⇒ Confirmation signal emitted
LiPo batteries:
Motor off at 3.0 V / cell
NiXX batteries:
Motor off at 6.0 V!
LiPo batteries:
Motor speed is reduced at 3.2 V /
cell
throttle stick to motor OFF
position
open throttle
completely at 2.9 V / cell
NiXX batteries:
Motor speed is reduced at 6.0 V
throttle stick to motor OFF position
open throttle
motor off
completely at 5.8 V / cell
⇒ Confirmation signal
emitted
Motor start-up time in
helicopter mode:
approx. 7.0 sec
in fixed-wing mode:
approx. 1.3 sec
Motor start-up time in
helicopter mode:
approx. 2.0 sec
in fixed-wing mode:
approx. 0.2 sec
⇒ Confirmation signal
emitted
7.
Select manual timing
→
only if automatic timing was previously set to OFF
(seven-times beep, continuously repeated)
7.1
For "hard" timing
(22 - 30 degrees)
→
stick to full-throttle
position
OR:
For "soft" timing (7 degrees)
→
stick to motor OFF
position
7.2
Stick to centre position
8.
Select pulse frequency
(eight-times beep, continuously repeated)
8.1
For 8 kHz pulse frequency
→
stick to full-throttle
position
OR:
For 16 kHz* pulse
frequency
motor off
→
stick to motor OFF
position
8.2
Stick to centre position
9.
Select model type
(nine-times beep, continuously repeated)
9.1
For helicopters (Governor
Mode)
→
stick to full-throttle
position
OR:
For fixed-wing models*
→
stick to motor OFF
position
10.
Quitting programming mode
10.1 Stick to centre position
10.2 Stick to motor OFF position
* Default setting / as supplied
7. BEC = (B
MULTIcont BL-15 speed controllers are equipped with a BEC
system: the receiver and servos are fed power from the flight
battery via the regulator; no separate receiver battery is required.
Never connect a separate receiver battery!
Please note that the MULTIcont BL-15 speed controller's BEC
power supply can only deliver a limited current to the receiving
system in the model:
The actual current drawn by a servo varies according to its
performance, the frequency of commands and – in particular –
the freedom of movement of the control surface linkages (!). This
means that it is essential to measure the current drain of the
⇒ Confirmation signal
emitted
Recommended for
in-runners
Recommended for
out-runners
⇒ Confirmation signal
emitted
⇒ Confirmation signal
emitted
Governor mode = constant
rotational speed maintained
In Governor mode the
Brake is automatically
switched OFF, even if you
previously selected Brake
On
⇒ Rising tone sequence
⇒ Rising tone sequence
sounds twice: the controller
is ready for use, the altered
parameters have been
stored
E
C
ATTERY
LIMINATOR
)
IRCUIT
Page 3/4
Publicidad
Tabla de contenido
