Quick-clamping nut
To change the abrasive tool easily without having to use any
additional tools, you can use the quick-clamping nut (15) in-
stead of the clamping nut (14).
The quick-clamping nut (15) may be used only for
u
grinding or cutting discs.
Only use quick-clamping nuts (15) that are in good work-
ing order and not damaged.
When screwing on, make sure that the printed side of the
quick-clamping nut (15) is not facing the grinding disc;
the arrow must be pointing towards the index mark (27).
Press the spindle lock button (1) to
(27)
lock the grinding spindle. To tighten
the quick-clamping nut, turn the grind-
ing disc firmly clockwise.
If the quick-clamping nut has been at-
tached correctly and is not damaged,
you can loosen it by hand by turning
the knurled ring anticlockwise. If the
quick-clamping nut is stuck, do not
attempt to loosen it with pliers – al-
ways use the two-pin spanner. Posi-
tion the two‑pin spanner as shown in
the figure.
Approved abrasive tools
You can use all the abrasive tools mentioned in these operat-
ing instructions.
-1
The permissible speed [min
] or the circumferential speed
[m/s] of the abrasive tools used must at least match the val-
ues given in the table.
It is therefore important to observe the permissible rota-
tional/circumferential speed on the label of the abrasive
tool.
max. [mm]
[mm]
D
b
s
180
8
–
22.2
230
8
–
22.2
180
4.2
–
22.2
230
4.2
–
22.2
180
–
–
230
–
–
100
27
–
M 14
125
30
–
M 14
Bosch Power Tools
[°]
-1
d
α
[min
] [m/s]
–
8500
80
–
6500
80
–
8500
80
–
6500
80
–
–
8500
80
–
–
6500
80
–
8500
80
–
6500
80
max. [mm]
[mm]
D
b
s
180
26
–
M 14
180
20
–
22.2
125
–
–
M 14
83
–
–
M 14
180
3.0
7
22.2
s
230
3.0
7
22.2
α
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Operation
Do not load the power tool so heavily that it comes to a
u
stop.
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Exercise caution when cutting slots in structural walls;
u
see the "Information on structural design" section.
Clamp the workpiece if it is not secure under its own
u
weight.
If the power tool has been subjected to a heavy load,
u
continue to run it at no-load for several minutes to
cool down the accessory.
Do not use the power tool with a cut-off stand.
u
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
English | 27
[°]
-1
d
α
[min
] [m/s]
–
8500
80
–
8500
80
–
8500
80
–
8500
80
> 0
8500
80
> 0
6500
80
1 609 92A 9HP | (25.03.2024)