Changing The Brushes; Optional Accessories - Virutex FR66P Manual De Instrucciones

10. USE OF PARALLEL GUIDE
Parallel guide is used for edge trimming and cutting
differently shaped grooves in accordance with various
profile shapes.
Parallel guide S (Fig. 6) is placed in base grooves T (Fig.
6) and secured in place using the two knobs U (Fig. 6).
NORMAL SQUARE ADJUSTMENT – Loosen the base
knobs, move the square to the required position and
then tighten the knobs in this position.
PRECISION ADJUSTMENT – Once the square has
been approximately positioned and held in place,
a further fine adjustment may be made. To do this,
loosen square fastening knob V (Fig. 6), turn the fine-
adjustment knob on guide W (Fig. 6) to the required
measurement, then tighten the square fastening knob
V (Fig. 6) again in this position. A full turn of the
knob moves the square by 1 mm, with a maximum
distance of 10 mm. The gauged fine-adjustment
indicator X (Fig. 6) can be moved separately from the
knob, so that it may be set to zero from any position
using the reference mark. When turning the knob W
(Fig. 6) after adjusting the indicator X (Fig. 6), both
elements will turn together, thereby indicating the
degree to which the square has been moved, with
each division representing an advance of 0.1 mm.
11. USE OF TEMPLATE GUIDES
Template guides are used for copy cutting of richly
shaped patterns. Selected template guide Y (Fig. 7)
is fixed to base T (Fig. 7) using the two screws Z (Fig.
7). When copying, a diffrence in size between the
template and the routed item becomes apparent. The
difference between the radius of the template guide
and the radius of the tool must always be taken into
account when preparing the template.
12. DUST COLLECTOR ATTACHMENT
To attach the dust collector connector A1 (Fig. 6),
place it in the central recess in base T (Fig. 6), with
the connection facing the back, and hold it in place
with screws B1 (Fig. 6). If trimming dovetails with the
Virutex PL11 model dovetailing attachment, guide
and position the dust collector connector as desired
so that the trimmer moves over the dovetailing
attachment better.
The dust collector connector A1 may be attached
either directly to the suction tubes of dust collectors
AS182K, AS282K or by using the smaller diameter and
lighter 6446073 standard dust collector attachment,
C1 (Fig. 6), which can then be attached to AS182K,
AS282K or any other industrial dust collector.
8
13. DUST COLLECTION NOZZLE SUPPLEMENT
To ensure that the suction of the machine is sufficient
when working with trimmer bits of less than 30 mm
in diameter, use the dust collection nozzle A1 (Fig. 6)
with the included supplement F1 (Fig. 6).
If you are using trimmer bits with a diameter of more
than 30 mm and up to 40 mm, remove the supplement
F1 (Fig. 6) from the dust collection nozzle A1 (Fig.
6) and work with only the nozzle. To re-attach the
supplement, simply press it firmly into the nozzle slot.

14. CHANGING THE BRUSHES

Disconnect the machine from the mains
before performing any maintenance
operations.
The brushes must be replaced when they reach the
minimum length of 5 mm. For this purpose, remove
the switch box A (Fig. 6) by removing the screws
which hold it in place. Remove plugs D1 (Fig. 8)
which hold brushes E1 (Fig. 8) and replace them with
new original VIRUTEX brushes, ensuring that they
slide smoothly through the guides. We recommend
running the unloaded machine for several minutes
after changing the brushes. Take the opportunity
to check the condition of the collector. If it shows
signs of burning or wear and tear, we recommend
bringing it to a VIRUTEX technical service centre for
repair. When reassembling switch box A, take care to
ensure that the cables are properly located inside it.
15. LUBRITATION AND CLEANING
The machine is delivered fully lubricated from the
factory and does not require any special care during
its working life. It is important to clean the machine
carefully after use, using a dry air jet.
Maintain the supply cable in perfect operating
conditions.

16. OPTIONAL ACCESSORIES

The following optional accessories may be supplied:
5000000 Dovetailing template PL11
6027020 Chuck Ø 6
6727020 Chuck Ø 1/4"
6446073 3.5 m Standard dust collector attachment.
Template guides:
7722168 External Ø 10 mm for 6 mm bits.
7722120 External Ø 12 mm for 8 mm bits.
7722121 External Ø 14 mm for 10 mm bits.