Publicidad
Idiomas disponibles
Idiomas disponibles
WARNING: Sharp moving chain. To prevent accidental
operation, ensure that battery is removed from the tool
before performing the following operations. Failure to do
this could result in serious personal injury.
nOTE: The cutters will dull immediately if they touch the
ground or a nail while cutting.
To get the best possible performance from your chain saw it is
important to keep the teeth of the chain sharp. Follow these
helpful tips for proper saw chain sharpening:
1. For best results use a 4.5 mm file and a file holder or filing
guide to sharpen your chain. This will ensure you always get
the correct sharpening angles.
2. Place the file holder flat on the top plate and depth gauge
of the cutter.
3. Figure R- Keep the correct top plate
of 30° on your file guide parallel with your chain (file at 60°
from chain viewed from the side).
4. Sharpen cutters on one side of the chain first. File from the
inside of each cutter to the outside. Then turn your saw
around and repeat the processes (2,3,4) for cutters on the
other side of the chain.
nOTE: Use a flat file to file the tops of the rakers (portion of
chain link in front of the cutter) so they are about 0.635 mm
below the tips of the cutters as shown in Figure s.
5. Figure T- Keep all cutter lengths equal.
6. If damage is present on the chrome surface of the top plates
or side plates, file back until such damage is removed.
CAUTION: After filing, the cutter will be sharp, use extra
caution during this process.
nOTE: Each time the chain is sharpened, it loses some of the
low kickback qualities and extra caution should be used. It
is recommended that a chain be sharpened no more than
four times.
Accessories
WARNING: The use of accessories not recommended in
this manual may be hazardous.
Replacement chain and bar are available from your nearest
D
WALT authorized service center. For use only with low kick
e
back bar and chain.
Available bars and chains for DCM565:
•
Bar:
30 cm service part number 90586162
Chain: 30 cm service part number N507302
•
•
DT20676-QZ – 30CM Oregon Chain 3/8" low pro, .0430" /
1,1mm (90PX045)
•
DT20665-QZ – 30cm Oregon Bar & Chain 30cm chain 3/8"
low pro, .043" / 1,1mm (90PX045) & 30CM bar
Optional Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Maintenance
Your D
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
The charger and battery pack are not serviceable.
Lubrication
21
filing angle line
Refer to Saw Chain and Guide Bar Oiling (Fig. L)
Cleaning
Protecting the Environment
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
•
•
WALT recommended
e
WALT power tool has been designed to operate
e
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
Run the battery pack down completely, then remove it from
the tool.
Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
EnGLIsh
49
Publicidad
