Publicidad
Idiomas disponibles
Idiomas disponibles
4. Ins
tallation
x Remov
ve all packing m
aterial from the
remove
ed.
x Clean t
the spray nozzle
e and make sure
he VDL900HZ
x Place t
horizontally on
x Pour hi
igh quality smok
ke liquid (VDLH
fluid lev
vel. Do not ove
rfill. Place the c
x Connec
ct the remote co
ontrol into the s
5. Use
e
a) The
Device
x Plug th
he remote contro
ol into the slot a
power
cord.
x Turn on
n the power swi
itch located at t
x The red
d light on the re
emote control w
x The de
vice must warm
m up. The period
minute
es.
x The gre
een light on the
e remote control
Remot
te Control").
b) The
Remote Contr
rol
Please re
efer the illustrat
ion on page 2.
1
pow
wer LED
smo
oke output ever
ry x minutes (m
2
30
min)
3
out
put volume
4
fixe
ed time open LE
ED
6. Not
tes
The V
VDP900HZ doe
es not feature a
pum
p will continue
e working. Alw
device can su
x If you e
experience low
output, mechan
Check
the fluid level, t
the external fus
working
g properly, plug
g in the unit aga
operati
ion to avoid per
rmanent damag
before
transporting th
e unit.
x Using t
the device will p
produce water d
x A little
smoke may con
ntinue to escape
7. DMX
X Connectio
on
a. DMX5
12 Connection
n
Connect
an XLR cable to
o the female 3-p
nput of the VDP
P900HZ. Multip
pin XLR i
cable sho
ould be a two-co
ore screened ca
b. DMX-5
512 Chain with
h Termination
c. DMX S
Start Address
All DMX-c
controlled devic
ces need a digita
This start
t address is the
channel numbe
Enter the
e correct numbe
er and read it fro
You can u
use the same st
tarting address
device.
09.11.201
0
VDP90
e shipping box. C
Check that all fo
e nothing is obs
structing the ou
a flat surface. R
Remove the liqu
HLH5) into the t
tank, being care
cap back on the
slot at the back
at the back of th
he device. Plug
the back of the
device.
will light up.
d depends on th
he conditions bu
l will go up once
e the machine is
5
max.
6
7
8
an automatic
stop function
ways monitor t
the tank fluid
uffer damage w
nical noise or no
o output at all, u
se, the remote c
control and the
ain. If the device
e will not functi
e. Return the de
evice to your de
rops at the noz
e from the nozz
zle after operatio
pin XLR output o
of your controlle
ple VDP900HZs
s can be linked
able with XLR in
put and output
n
A DMX term
minator is recom
mmended for ins
to run a lon
g distance or is
The termina
ator prevents co
orruption of the
noise. The D
DMX terminator
between pin
ns 2 and 3, whic
ch is then plugg
the last dev
vice in the chain
al start address
er from which th
he device starts
om the display
for a whole gro
oup of devices o
4
0HZ
oam and plastic
tput.
uid tank cap.
eful not to excee
liquid tank and
tighten.
of the device.
the device into
ut should not tak
s ready to opera
output LED
successive s
spraying for x se
seconds)
heated over
r LED
spray button
n
when running
level during o
when run with
hout fluid!
unplug the devi
power cord. If a
on after 30 seco
ealer. Remembe
zle. This is perf
fectly normal.
on.
er and the other
through serial l
connectors.
tallations where
in an electrical
ly noisy environ
digital control s
is simply an XL
LR plug with a 1
ged into the XLR
. Please see illu
ustration.
so that the cor
rrect device resp
s to "listen" to th
base of the VDP
located on the b
r enter an indiv
c padding is
ed the maximum
m
the mains usin
g the
ke more than 10
0
ate (see "The
econds (max. 1
5
g out of fluid; t
the
operation as th
he
ce immediately
.
all appears to be
e
onds, discontinu
ue
er to drain the t
tank
r side to the ma
ale 3-
inking. The link
king
e the DMX cable
e has
nment (e.g. disc
cos).
signal by electri
cal
120
resistor
R output socket
of
ponds to the sig
gnals.
he DMX controll
ler.
P900HZ.
vidual one for ev
very
©Vellema
an nv
Publicidad
