Publicidad
Idiomas disponibles
Idiomas disponibles
Do not store explosive substances such
13.
as aerosol cans with a flammable propellant
in this appliance.
This appliance is intended to be used in
14.
household and similar applications such as:
- Staff kitchen areas in shops, offices and
other working environments;
- Farm houses and by clients in hotels,
motels and other residential type environ-
ments;
- Bed and breakfast type environments;
- Catering and similar non-retail applica-
tions.
At the end of the functional life of your
15.
appliance containing cyclopentane gas in
the insulation foam and perhaps R600a gas
(isobutane) in the refrigeration circuit - it
should be made safe before being sent to
the dump. For this operation, please con-
tact your dealer or the Local Organisation
in charge of waste disposal.
Do not damage the refrigeration circuit.
16.
17.
Keep ventilation openings, in the appli-
ance enclosure or in the built-in structure,
clean and clear of obstruction.
Fuse replacement
If the mains lead of this appliance is fitted with a BS
1363A 13 amp fused plug, to change a fuse in this type
of plug use an A.S.T.A. approved fuse to BS 1362 type
and proceed as follows:
1. Remove the fuse cover and fuse.
2. Fit replacement 13A fuse into fuse cover.
3. Refit both into plug.
Important: The fuse cover must be refitted when
changing a fuse and if the fuse cover is lost the plug
must not be used until a correct replacement is fitted.
Correct replacement is identified by the colour insert or
the colour embossed in words on the base of the plug.
Replacement fuse covers are available from your local
electrical store.
Connection to a rewireable plug
If the fitted plug is not suitable for your socket outlet,
then is should be cut off and disposed of in order to
avoid a possible shock hazard should it be inserted into
a 13A socket elsewhere. A suitable alternative plug
should then be fitted to the cable. The wires in this
mains lead are coloured in accordance with the follow-
ing code; BLUE - neutral ("N") BROWN - live ("L")
GREEN AND YELLOW - earth ("E")
1. The GREEN AND YELLOW wire must be connected
to the terminal in the plug which is marked with the
letter "E" or by the Earth symbol or coloured green or
EN
___
green and yellow.
2. The BLUE wire must be connected to the terminal
which is marked with the letter "N" or coloured
black.
3. The BROWN wire must be connected to the
terminal which is marked with the letter "L" or
coloured BROWN or RED which is connected to
the fuse.
INSTALLATION
___________________________________________
To ensure that the appliance operates properly and to
reduce energy consumption, it is important that the
appliance is installed correctly.
Ventilation
The compressor and condenser generate heat and,
therefore, need to be ventilated properly. Rooms with
no ventilation are not suited for installation of the
ppliance. Therefore, it should be installed in a room with
an opening (window or French window) that provide the
appropriate amount of air re-circulation. It is also
important to install it in a free humidity room.
During installation, make sure not to cover or obstruct
the grates that allow for proper ventilation of the
appliance.
For proper ventilation of the appliance, leave a space of
at least 10 cm between the sides of the appliance and
any adjacent cabinets/walls.
Away from Heat
Avoid positioning the appliance in a place where it is
directly exposed to sunlight or near an oven, cook top or
the like.
Electrical and Earth Connection
The appliance should not be turned on right after
transportation. Two hours is the advised time so that
the oil from the motor-compressor gets back to its
original position. Before proceeding with the electrical
connection, make sure that the voltage indicated on the
rating plate, corresponds to the mains voltage in your
home and that the socket is fitted with a standard earth
wire in accordance with safety standards. If the socket
is not fitted with an earth wire, the manufacturer will
not be held liability for any damages and or injuries
arising out of the use of the appliance. Do not use
multiple sockets or adapters. Position the appliance in
such a way that you can access the socket where it is
plugged in.
Electrical power
The electrical socket must be able to handle the maxi-
mum power load of the appliance, which is indicated on
the rating plate located in the back of the appliance.
THE APPLIANCE
___________________________________________
A -
Temperature adjustment knob
By turning the knob from setting Min (1) to setting
Max (4/5) allows adjusts the temperature inside the
freezer.
B -
Warning Indicator(red light)
When this red warning light comes on for a prolonged
5
Publicidad
