Descargar Imprimir esta página

Maytag MAT14PD Instrucciones De Instalación página 4

Ocultar thumbs Ver también para MAT14PD:

Publicidad

Idiomas disponibles

Idiomas disponibles

INSTALLATION REQUIREMENTS
Gather the required tools and parts before starting installation.
Tools
needed
[] Level
[]
Flat-bladescrewdriver
[] Utility knife
[]
Pliers
[] Scissors
[]
Bucket
[] 200 mm (8") or 250 mm
(10") adjustable wrench
Parts supplied
Remove parts bag from washer. Check that all parts were
included.
[]
1 Hose clamp
[] 2 Front-leveling
legs
[]
2 inlet hoses
with nuts
[]
4 Flat water hose washers
[] 1 Drain hose
[] Hose adapter
Technical
C{othes
Specifications:
Capacity:
220 - 240 V, 50 Hz. AC
MAT14PD: 5.9 Kg Max.
650 Watts
iMPORTANT:
Do not install or store the washer where it will
be exposed to the weather. Do not store or operate the washer
in temperatures
at or below 0°C (32°F). Some water can remain
in the washer and can cause damage in low temperatures.
Proper installation is your responsibility.
You wii{ need:
[] A water heater set to deliver 60°C (140°F) water to the washer.
[] An earthed electrical outlet located within 1.2 m (4 ft) of where
the power cord is attached to the back of the washer. See
"Electrical Requirements."
[] Hot and cold water taps located within 1.2 m (4 ft) of the back
of the washer, and provide water pressure of 69-690 kPa
(10-100 psi). A pressure reduction valve should be used in the
supply line where inlet pressure entering the building exceeds
690 kPa (100 psi) to prevent damage to the washer mixing
valve.
[] A level floor with a maximum slope of 25 mm (1 ") under entire
washer.
[] A sturdy floor to support the washer weight (washer, water,
and load) of 143 kgs (315 Ibs).
[] A 300 mm (12") minimum riser to provide an air cushion and
prevent noise and damage to valves for a single washer
installation.
[] A floor drain should be provided under the bulkhead.
Prefabricated
bulkheads with electrical outlets, water
supply lines, and drain facilities should be used only
where local codes permit.
NOTE: Front access to the pump area is available by removing
No. T20 TORX _'_*t security screws and then removing the front
panel.
Recessed Area and Closet installation
instructions
This washer may be installed in a recessed area or closet.
The installation spacing is in inches and is the minimum
allowable. Additional spacing should be considered for ease
of installation, servicing, and compliance with local codes
and ordinances.
if closet door is installed, the minimum unobstructed
air
openings in the top and bottom are required. Louvered doors
with equivalent air openings are acceptable.
Closet door
__
OO
432 mm
(17")
_
................................
0mm
"_
4_
(0")
Recessed front wew
3.10 m2
(48 in2)*
(24
0mm
•_- (0">
mm
(4") min.
Closet side view
Front
View
3.10 m_
(48 in_) *
÷
1.55m _
(24 in_) *
0
76 m{
(3")
Closet
door
76 mm
(3 II
*Opening is the minimum for a closet door.
Louvered doors with equivalent air openings are acceptable.
[] Additional spacing should be considered for the ease of
installation and servicing.
[] Additional clearances may be required for wall, door, and floor
mouldings.
[] Additional spacing of 25 mm (1 ") on all sides of the washer is
recommended
to reduce noise transfer.
[] Companion spacing should also be considered.
®1 Torx is a registered trademark
of Saturn Fasteners, Inc.
4

Publicidad

loading