Publicidad
Idiomas disponibles
Idiomas disponibles
English
Separate the push lever from the workpiece.
(4)
Next, point the stapler downward and release the
trigger lock button, then pull the trigger and then wait in
that position for 5 seconds or longer.
–
THE STAPLER MUST NOT OPERATE.
(5)
A: Without touching the trigger, depress the push lever
against the workpiece. Next, pull the trigger.
–
THE STAPLER MUST OPERATE.
B: Hold the trigger back and depress the push lever
against the workpiece again.
–
THE STAPLER MUST NOT OPERATE.
C: Separate the finger from the trigger. Next, A is operated
again.
–
THE STAPLER MUST OPERATE.
(6)
If no abnormal operation is observed, you may load
staples in the Stapler.
Drive staples into the workpiece that is the same type to
be used in the actual application.
–
THE STAPLER MUST OPERATE PROPERLY.
5. Loading staples
WARNING
When loading staples into Stapler,
1) remove battery from the stapler;
2) do not pull trigger; and
3) do not depress push lever.
NOTE
○ Do not simultaneously load staples of different lengths.
○ Do not consecutively load several staple strips that
have a small number of staples.
Doing so may cause a staple jam or other problems.
(1) Press the stop lever, and pull out the magazine base.
(Fig. 6)
(2) Put the staples into the magazine with their legs pointed
up. (Fig. 7)
(3) Press in the magazine base to its original position, and
the stop lever will lock it. (Fig. 8)
NOTE
Gently close the magazine base.
If it is closed forcefully, the staple strips may become
deformed and prevent the magazine base from closing.
The Stapler is now ready to operate.
HOW TO USE THE STAPLER
WARNING
○ NEVER point tool at yourself or others in work area.
○ Keep fingers AWAY from trigger when not driving
staples to avoid accidental firing.
○ Do not use the electrical cord if damaged. Have it
repaired immediately.
○ Never place your face, hands or feet near firing head
when using.
○ Do not drive staples on top of other staples or with
Stapler at too steep of an angle; staples can ricochet
and hurt someone.
○ Do not drive staples into thin boards or near corners
and edges of workpiece. Staples can be driven through
or away from workpiece and hit someone.
○ Never drive staples from both sides of a wall at the
same time. Staples can be driven into and through the
wall and hit a person on the opposite side.
○ Never use Stapler which is defective or operating
abnormally.
○ Do not use Stapler as hammer.
○ Remove all remaining staples and battery from stapler
when:
1) doing maintenance and inspection;
2) checking proper operation of push lever and trigger;
3) cleaning a jam;
4) it is not in use;
5) leaving work area;
6) moving it to another location; and
7) handing it to another person.
○ Remove battery from Stapler when loading staples.
1. Stapling procedures (Fig. 9)
This Stapler is equipped with the push lever and does
not operate unless the push lever is depressed.
First, press the push lever against the wood; next, pull
the trigger to drive the staple.
After stapling once, stapling will not be possible again
until the trigger is released and pull again.
WARNING
○ To avoid double firing or accidental firing due to recoil.
Pull the trigger rapidly and firmly.
A: Position the staple outlet on the workpiece with finger
off the trigger.
B: Depress the push lever firmly until it is completely
depressed.
C: Pull the trigger to drive a staple.
D: Remove finger from the trigger and lift the tool off the
wood surface completely.
To continue stapling in a separate location, move the
stapler along the wood, repeating from the step A as
required.
NOTE
○ Operations B and C should be done within 4 seconds of
each other. If more than 4 seconds pass after B, the
Stapler will not work properly. If this happens, retry from
B.
○ If the staples are not being driven in completely, firmly
press down on the head of the stapler when firing.
(Fig. 10)
WARNING
○ Keep your finger off the trigger except during stapling
operation, because serious injury could result if the
push lever accidentally contacts you or others in work
area.
○ Keep hands and body away from the discharge area.
This HiKOKI stapler may bounce from the recoil of
driving a staple and unwanted subsequent staple may
be driven, possibly causing injury.
NOTE
○ Always handle staples and package carefully. If staples
are dropped, collating bond may be broken, which will
cause mis-feeding and jamming.
○ After stapling:
1) remove battery from the Stapler;
2) remove all staples from the Stapler;
2. Using the hook (See Fig. 11)
WARNING
When using the hook, remove the battery. Pay sufficient
attention so that the main equipment does not fall.
If the tool falls, there is a risk of accident.
Hook can be installed on the left or right side.
A: Remove the battery, then remove all remaining staples
from the magazine.
B: Securely hold the main unit and remove the screw using
a screwdriver.
C: Remove the hook.
12
Publicidad
