Problem
Smoke is coming out of the baking
chamber or the air vents.
The bread collapses in the middle
and is moist at the base.
The ingredients were not mixed
correctly or the bread did not bake
properly.
The baking machine will not start
and the display shows "HHH"
The bread rises too quickly
Tips and answers
The bread does not rise at all or
hardly rises
The bread collapses in the middle
Heavy, lumpy texture
Bread is not baked in the middle
Bread/crust is too light
24
Cause
Solution
The ingredients are in the baking
Pull out the plug and clean the
chamber or are sticking to the
outside of the baking pan or the
outside of the baking pan.
baking chamber.
Remove the bread from the baking
The bread has been left in the bak-
pan before the keep-warm func-
ing pan too long after baking.
tion turns off.
Check the chosen programme as
Wrong programme settings
well as the settings for the bread
chosen.
size and browning level
The lid should not be opened other
The lid was regularly opened
than to add extra ingredients.
during the baking process.
The lid must then be closed
immediately afterwards.
Check to see if the dough hook
is blocked by peppercorns etc.
Remove the baking pan and check
The dough hook will not twist.
if the dough hook can be twisted.
If this is not the case, send the
appliance for repair.
You must stay on the current
The internal temperature is too
programme. Open the lid and leave
high.
the bread maker to cool down for
10 to 20 minutes.
Check the amounts of ingredients
Too much yeast, too much flour or
used, adjust if necessary and check
too little salt
that all ingredients have been
added to the mix.
Check the amounts of ingredients
No yeast or too little yeast or the
used, adjust if necessary and check
wrong amount of water
that all ingredients have been
added to the mix.
The yeast came into contact with
Make sure that you fill the baking
the liquid too soon
pan in the correct order.
Check the ingredient quantities
used and adjust if necessary. If
There is too much dough for the
ingredients that contain liquid are
size of the baking pan
used, the amount of water must
be reduced accordingly.
Make a little hollow in the flour
The yeast came into contact with
and add the dry yeast, avoiding
the liquid too soon
any direct contact between the
water and the dry yeast.
Check the amounts of ingredients
used, adjust if necessary and check
Too much flour or too little water
that all ingredients have been
added to the mix.
Check the amounts of ingredients
used, adjust if necessary and check
Not enough yeast or sugar
that all ingredients have been
added to the mix.
Check the amounts of ingredients
used, adjust if necessary and check
Too much water
that all ingredients have been
added to the mix.
Since the bread maker does not
have a heat source around the
lid, it is recommended that you
Wrong browning level chosen
use the maximum browning level
if you want your bread to have a
crispy texture.
For UK use only
▪ This product is supplied with a 13 A plug conforming to BS 1363 fitted to the mains lead. If the
plug is unsuitable for your socket outlets or needs to be replaced, please note the following. If the
plug is a non-rewireable one, cut it from the mains lead and immediately dispose of it. Never insert
it into a socket outlet as there is a very great risk of an electric shock
▪ The replacement of the plug at the mains lead has to be done according to the following
instructions:
Important: The wires in this mains lead are coloured in accordance with the following code:
blue
Neutral
brown
Live
As the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows
⋅
the wire which is coloured blue must be connected to the terminal which is marked with the
letter N or coloured black,
⋅
the wire which is coloured brown must be connected to the terminal which is marked with
the letter L or coloured red.
Do not connect any wire to the terminal which is marked with the letter E or by the earth
symbol
, or coloured green or green and yellow.
▪ If a 13 A (BS 1363) plug is used it must be fitted with a 3 A fuse conforming to BS 1362 and be
ASTA approved. If any other type of plug is used, the appliance must be protected by a 5 A fuse
either in the plug or adapter or at the distribution board.
If in doubt - consult a qualified electrician.
▪ Never use the plug without closing the fuse cover.
The device complies with the European Directives 2014/35/EU, 2014/30/EU and
2009/125/EU.
At the end of its service life, this product may not be disposed of in the normal
household waste, but rather must be disposed of at a collection point for
recycling electrical and electronic devices. The materials are recyclable according
to their labelling. You make an important contribution to protecting our
environment by reusing, recycling or utilising old devices in other ways. Please ask
the municipal administration where the appropriate disposal facility is located.
Subject to change.
25