Roborock S8 MaxV Ultra Manual Del Usuario página 10

good WiFi coverage and a power outlet
or power strip nearby. Reserve a space
of at least 0.305 m (1 ft) in height, 0.42 m
(1.4 ft) in width, and 1 m (3.3 ft) in depth
for placing the dock, ensuring both sides
and the front are free of obstructions that
could impede the robot from docking and
departing.
4. It is strictly prohibited to place the dock in
damp, sun-exposed, or rainy environments.
5. There should be no thresholds, slide
rails, or steps higher than 0.02 m (0.8 ft)
between the dock and the cleaning area
to prevent the robot from missing spots
and getting stuck.
6. Please avoid arranging pipes through
doorways or corridors.
B2-1—Tap Water Supply
B2-2—Three-Prong Power Outlet
B2-3—Floor Drain or Sewer Pipe
B2-4—More than 0.305 m (1 ft)
B2-5—More than 1 m (3.3 ft)
B2-6—More than 0.42 m (1.4 ft)
Notes:
Before installing, disconnect the power supply of
the dock, and close the main water valve, faucet
valve or angle valve. Drain pipelines, ensure they are
connected without leakage, and then power on the
dock.
All installation diagrams are for reference only. The
actual installation situation may vary.
Install the Dock Base
B3-1— Place the dock on the reserved space
and remove the foam used to secure
the mop washing module in shipment
at the bottom.
B3-2— Attach the dock base by pressing down
both sides of the base firmly, and then
pressing the connecting part in the
middle until you hear a click.
Connect the Power Cord
Plug the power cord firmly into the dock
power port, and keep the excess cord inside
the storage slot.
Note: Make sure to insert the power plug all the way in
and do not connect to the power supply.
Connect the Water Inlet and
Outlet
B5-1— Press the snap ring at the connector
against the elbow and at the same
time, pull out the plugs of the water
inlet and outlet in the opposite
direction.
B5-2— Rotate the water inlet and outlet to
directions suitable for installation.
Connect one ends of the 1/4" pipe
and 3/8" pipe to the corresponding
positions, insert the corresponding
lock plate into the slim space
between the snap ring and elbow,
and then snap the pipelines into the
slots.
Notes:
Slightly lift the dock when rotating the water inlet elbow.
10
When installing the pipes, make sure to insert them all
the way in.
Store the plugs removed from the dock and additional
pipes and lock plates properly.
Connect to Refill Pipeline
Make sure to close the tap water valve that
supplies water to the dock. After confirming
that the faucet or angle valve is closed,
install the tap water filter in the correct
direction to the 1/2" water inlet of the clean
water three-way valve. Then, connect the
1/2" water inlet and 1/2" water outlet of the
clean water three-way valve to the water
inlet pipeline. Finally, connect the other end
of the cut-to-fit 1/4" pipe to the 1/4" water
outlet of the clean water three-way valve
and insert the lock plate into the snap ring.
B6-1—Tap Water Supply
B6-2—1/2" Water Inlet
B6-3—Tap Water Filter
B6-4—1/4" Lock Plate
B6-5—Snap Ring
B6-6—1/4" Water Outlet
B6-7—Clean Water Three-Way Valve
B6-8—Gasket
B6-9—1/2" Water Outlet
B6-10—Inlet Pipe (1/4" Pipe)
Notes:
Only connect to room temperature tap water, rather
than reclaimed water or hot water.
The tap water filter must be installed strictly following
the instructions. If installed in the reverse direction, it
could be damaged.
If the 1/2" water outlet does not need to be connected
to a water pipe, use a suitable valve cap instead.