Roborock S8 MaxV Ultra Manual Del Usuario página 9

A11-5—Cleaning Tank of Edgewise
Mopping Module
A11-6—Dock Base
A11-7—Cleaning Solution Cartridge
A11-8—Dust Bag Slot
A11-9—Filter
A11-10—Dock Location Beacon
A11-11—Suction Inlet
A11-12—Water Filter
A11-13—Status Indicator Light
Breathing: Emptying/Mop washing
Red: Dock error
Dim: Charging/Drying
Off: Powered off
Note: To minimize disturbance, the indicator light will be
off or dim in Do Not Disturb (DND) mode.
A11-14—Mop Washing Module
A11-14-1—High-Speed Maintenance Brush
A11-14-2—Washing Strip
A11-14-3—Water Outlets
A11-14-4—Maintenance Brush Latch
Power Cord Storage
A12-1—Cord Storage Slot
A12-2—Power Port
A12-3—Cord Outlets
A12-4—Water Pipe Slot
A12-5—Water Inlet
A12-6—Water Outlet
Note: Power cord can exit at either side.
Installation Accessories
A13-1—Inlet Pipe (1/4" pipe) × 1
A13-2—Drainpipe (3/8" pipe) × 1
A13-3—Harness Tube × 1
A13-4—1/4" Lock Plate × 5
A13-5—3/8" Lock Plate × 3
A13-6—Tap Water Filter × 1
A13-7—Clean Water Three-Way Valve
(Gasket Pre-Installed) × 1
Refill and Drainage Pipes
A14-1—Tap Water Supply
A14-2—Tap Water Filter
A14-3—Clean Water Three-Way Valve
A14-4—3/8" Square Elbow
A14-5—3/8" Lock Plate
A14-6—Harness Tube
A14-7—Drainpipe (3/8" pipe)
A14-8—Floor Drain or Sewer Pipe
A14-9—Dock Power Cord
A14-10—1/4" Lock Plate
A14-11—1/4" Square Elbow
A14-12—Snap Ring
A14-13—Inlet Pipe (1/4" pipe)
Installation
B
Important Information
B1-1— Tidy cords, hard or sharp objects
(such as nails and glass), and loose
items from the ground and move
any unstable, fragile, precious, or
dangerous items to prevent personal
injury or property damage due to
09
items becoming tangled in, struck by,
or knocked over by the robot.
B1-2— When using the robot in a raised
area, always use a physical security
barrier to prevent accidental falls
that may result in personal injury or
property damage.
Notes:
When using the robot for the first time, follow it
throughout its whole cleaning route and watch for
potential problems. The robot will be able to clean by
itself in future uses.
To prevent excessive buildup of dirt on the mop cloths,
floors should be vacuumed at least three times before
the first mopping cycle.
Check the Installation
Environment
Before installation, check whether the
following requirements are met and identify
the water inlet, outlet, and placement
locations for the dock in your home:
1. The water inlet pressure range should
be 0.1-0.4 MPa. If it exceeds 0.4 MPa, a
pressure-reducing valve should be installed.
2. The diameter of the drainpipe outlet
should be no less than 0.015 m (0.05
ft). The height difference between the
highest point of the drainage pipe and
the floor surface where the dock is placed
should not exceed 1 m (3.3 ft), preferably
not exceed 0.5 m (1.6 ft).
3. The dock should be placed against a wall
on a hard, flat surface (wood/tile etc.) with