Publicidad
Idiomas disponibles
Idiomas disponibles
Unscrew the nozzle for the outer burner ring w1
6.
(WAF 10).
→ Fig.
28
Check that the O-ring is seated correctly in the
7.
new main control nozzle for the inner burner ring.
Fit the nozzle w2 onto the burner pipe.
8.
Screw the new main control nozzle for the outer
9.
burner ring w1 as far as it will go into the nozzle
retaining head.
Fit the nozzle retaining head onto the burner
10.
pipes.
Fit the securing clips.
11.
Adjusting the main control nozzles on the wok
burner
Unscrew the fastening screw.
1.
→ Fig.
29
Adjust the air regulating valve to the correct set-
2.
ting.
The setting depends on the gas type → Fig.
Tighten the fastening screw.
3.
Replacing the main control nozzles on the stand-
ard output burners and high output burners
Remove the securing clips from the burner pipes.
1.
→ Fig.
30
Pull out the burner pipes.
2.
The electrode can remain connected.
Unscrew the burners (Torx T20) and pull out the
3.
burner pipes.
→ Fig.
30
Pull the nozzles off the burner pipes by hand.
4.
Pull off the O-ring.
5.
Check that the O-ring is seated correctly in the
6.
new main control nozzles.
Fit the nozzles to the burner pipes. Take care not
7.
to bend the burner pipes when doing so.
Fit the burners onto the burner pipes.
8.
Fit the securing clips.
9.
Screw the burners tightly into place.
10.
Adjusting the main control nozzles on the standard
output burners and high output burners
Unscrew the fastening screw.
1.
Adjust the air regulating valve on the outer burner
2.
L1 → Fig.
to the correct setting.
40
→ Fig.
31
Tighten the fastening screw.
3.
Adjust the air regulating sleeve on the inner
4.
burner L2 → Fig.
to the correct setting by turn-
40
ing or pushing it.
→ Fig.
31
Screwing the hob in place
Put the hob in place and tighten the screws
▶
evenly.
Fitting burner parts
Fit the burner parts and position them correctly.
▶
→ Fig.
26
Fitting the pan supports
Fit the pan supports and position them correctly.
▶
→ Fig.
27
Switching gas type using the control knob
Turn any control knob to 0.
1.
→ Fig.
32
Disconnect the appliance from the mains power
2.
supply.
→ Fig.
33
Wait at least 30 seconds.
3.
Reconnect the appliance.
4.
→ Fig.
34
The illuminated ring around the control knob lights
a
up green for a few seconds and then yellow.
→ Fig.
35
Wait until the illuminated ring goes out.
5.
While the control knob is pushed in, carry out the
6.
following steps without interruption:
Turn the control knob one notch anti-clockwise
‒
to 12
Turn the control knob three notches clockwise
‒
to 1
.
Turn the control knob two notches anti-clock-
‒
wise to 0
→ Fig.
36
The illuminated ring on the control knob lights up
a
.
40
yellow.
Set the gas type on the control knob.
7.
→ Fig.
37
If the control knob is on the gas type currently set,
the illuminated ring on the control knob lights up
green.
Control knob position
2
3
4
6
Leave the control knob at the required setting for
8.
at least 5 seconds.
The illuminated ring around the control knob lights
a
up green.
To save the setting, while the control knob is
9.
pushed in, carry out the following steps without in-
terruption:
Turn the control knob to 0
‒
Turn the control knob one notch anti-clockwise
‒
to 12
Turn the control knob three notches clockwise
‒
to 1
.
Turn the control knob two notches anti-clock-
‒
wise to 0
→ Fig.
38
The illuminated ring goes out.
a
The setting has been saved.
a
The illuminated ring around the control knob lights
a
up yellow for a few seconds.
Wait until the illuminated ring goes out.
10.
Checking that the appliance is working after con-
version
After converting the gas type, check the appliance
1.
for leaks.
Make sure that yellow tips are not visible on the
2.
flames.
When turning the control knob quickly between
3.
the highest and the lowest setting, make sure that
the burner does not go out and that no flashback
occurs.
Documenting the gas type conversion
Attach the sticker showing the new gas type next
▶
to the rating plate on the appliance.
.
.
Gas type
G20-20 mbar/G25-25
mbar
G30-29 mbar/G31-37
mbar
G30-50 mbar
G25-20 mbar
.
.
.
17
Publicidad
