DeWalt DCF680 Manual De Instrucciones página 7

Two-Position Screwdriver (Fig. B)
DCF680
To convert the tool to an angled screwdriver push on the
release button and rotate the top portion of the tool
10
as shown.
Quick-Release Chuck (Fig. A)
DCF680, DCF682
nOTE: The quick-release chuck
hex accessories only.
To install a bit, insert the bit into the quick-release chuck
until the clip locks it in place.
To remove a bit, pull the quick-release chuck forward.
Remove the bit and release the quick-release chuck.
Magnetic Bit Holder (Fig. A)
DCF681
nOTE: The magnetic bit holder
hex accessories only.
To install a bit, insert the bit into the magnetic bit holder
until the magnet holds it in place.
To remove a bit, pull it out of the magnetic bit holder.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start‑up can
cause injury.
Installing and Removing the Battery Pack (Fig. C)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in
the tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button 5 and firmly pull the battery pack out of the tool
handle. Insert it into the charger.
Proper Hand Position (Fig. F)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the main
handle .
14
Torque Adjustment Collar (Fig. B)
DCF680
The torque adjustment collar
and a 'MAX' symbol. The higher the number on the collar,
the higher the torque. To lock the clutch for fastening
operations, move to the 'MAX' position. Failure to do this
will allow the clutch to slip while attempting to fasten.
Performing an Application (Fig. A, E, F)
DCF680, DCF682
Insert the appropriate hex shank bit into the quick-
release chuck 8 .
DCF681
Insert the appropriate hex shank bit into the magnetic bit
holder 7 .
8 accepts 1/4" (6.4 mm)
7 accepts 1/4" (6.4 mm)
6 into the tool handle, align the
9 is marked with numbers
Screwdriving
Your screwdriver uses gyroscopic technology to sense your
hand motion. To operate:
1. Grasp the screwdriver as shown in Figure F and ensure
that the lock-off switch 2
2. Press and hold in the motion control activation
trigger 1 .
3. When the LED worklight
for use.
a. To tighten, rotate your hand clockwise.
b. To loosen, rotate your hand counterclockwise.
4. To turn the tool off, release the motion control
activation trigger.
Variable Speed
The spindle speed is dependent upon the amount
of rotation.
• small rotations operate the tool at a slower speed.
• large rotations operate the tool at a higher speed.
nOTE: For best performance, screw into pre-drilled holes.
If you wish to increase the spindle speed, rotate your hand
further in the same direction.
If you wish to decrease the spindle speed, rotate your hand
back toward the initial starting point.
Operation as a Deburring Tool (Fig. A, F)
DCF681

WARNING: Always keep hands and clothing away from
the cutting area of the tool.

WARNING: Only retract the cone
a pipe end. Do not lock the cone in the retracted position.
NOTICE: When deburring it is recommended to leave a hex
bit in the magnetic holder. Metal chips and shavings caused
by deburring can be picked up by the magnet in the holder.
1. Activate the tool by pressing the motion control
activation trigger 1 and rotating the tool in the
desired direction.
2. Slowly feed into pipe and press cone against burred
pipe end.
nOTE: Tool should be active before engaging with the pipe.
3. With tool actively rotating, firmly depress cone against
the pipe, engaging the cutter
multiple rotations to fully deburr the pipe end.

WARNING: Tool can stall, causing a sudden twist. To
reduce the risk of injury, always use proper hand position as
shown, and always hold securely in anticipation of the tool
cutter binding.
4. Once pipe end is deburred, pull the tool out of pipe and
then release the trigger.

WARNING: Before and after each use, inspect the cone
for proper closing. Do not operate the tool if the cone does not
move freely and close instantly.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start‑up can
cause injury.
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
English
is in the unlocked position.
3 illuminates the tool is ready
11 by pressing against
12 with pipe end. Allow
7