Silverline 262212 Traducción Del Manual Original página 10

EN
Cleaning
WARNING: ALWAYS wear protective equipment including eye protection and gloves when
cleaning this tool.
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the device's service life.
• Clean the body of your machine with a soft brush, or dry cloth.
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent
on a damp cloth is recommended.
• Water must never come into contact with the tool.
• Ensure the tool is thoroughly dry before using it.
• If available, use clean, dry, compressed air to blow through the ventilation holes
(where applicable).
Lubrication
This drill press comes correctly lubricated with grease and oil for the spindle mechanism parts which
will be sufficient for years of normal occasional use. However, if the drill press is frequently used,
it may need to be re-lubricated on a yearly basis. Instructions on dismantling and re-assembling
the spindle section are beyond the scope of this manual. However, general advice for lubrication
is as follows:
1. After dismantling, clean the components removing the old lubrication and check for excessive
component wear or damage.
2. Lubricate the Bearings (19) with a good quality lithium-based grease. Fill the Spline Sleeve (18)
and Spindle Sleeve (20) with grease and ensure the Spindle (21) is also greased.
3. A light coating of engine oil can be applied for parts where grease cannot be applied or where
there is surface friction.
Storage
• Store this tool carefully in a secure, dry place out of the reach of children.
• If the tool is permanently set up in a workshop or garage, ensure access is restricted to prevent
children operating the tool.
Troubleshooting
Problem
Drill press will not start
Abnormal or high levels of operating
noise
Drill bit smoking and excessive heat
Drill bit wobbles or runs out
Drill bit binds in workpiece
10
Possible Cause
Mains connection not correct
Mains plug fuse blown
Pulley Cover (4) not closed
ON/OFF Switch (3) faulty or another tool fault
Incorrect belt tension
Spindle needs lubricating
Worn or damaged pulley drive belt
Loose screws or other fittings
Speed setting incorrect
Blunt drill bit
Material or drill bit should not be drilled dry
Bent drill bit
Drill bit not centrally located in Chuck (7)
Worn spindle bearings or other parts
Pulley belt has incorrect low tension
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222.
Web: www.silverlinetools.com
UK Address:
Toolstream Ltd.
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
EU Address:
Toolstream B.V.
Hogeweg 39
5301 LJ Zaltbommel
The Netherlands
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional
and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with
household waste.
• Contact your local waste disposal authority for information on the correct way to dispose of
power tools.
Check mains plug is fully inserted in socket and socket is switched on. If RCD is fitted check that it is reset/on
Check fuse in mains plug and replace if necessary with same value
Ensure Pulley Cover is fully closed and securely fastened. If necessary also check the safety switch mechanism inside
the Pulley Cover is not damaged
Contact your Silverline dealer or authorised service centre
Adjust tension (see 'Adjusting speed')
See 'Maintenance' . Contact your Silverline dealer or an authorised service centre if necessary
Replace belt. Contact your Silverline dealer or www.toolsparesonline.com for a replacement belt
Check body of tool and inside Pulley Cover to make sure all parts are secure and correctly fitted
Change speed (see 'Adjusting speed')
Replace or sharpen drill bit
Use lubricant or cutting fluid
Replace drill bit
Refit drill bit in Chuck
Contact your Silverline dealer or an authorised service centre
Adjust tension (see 'Adjusting speed')
Solution