Publicidad
7.3.2 The FM receiving frequency range of this product can be adjusted according to needs. There are three receiving ranges:
In the FM working state, lightly press the [
continuously, and you will see the three numbers 64MHZ , 76MHZ, and 87.5 MHZ changing in rotation on the main screen. If you select
64MHZ, it means that the selected receiving frequency band is 64-108MHZ, and so on.
Home screen display value
64MHZ
76MHZ
87.5MHZ
After stopping the operation, it will automatically exit the settings and automatically default to the last selected frequency band
settings.
7.3.3 The MW step value of this product, 9KHZ/10KHZ, can be adjusted according to needs.
In the MW working state, lightly press the [
continuously, and you will see the two values of 520KHZ and 522KHZ changing in rotation on the main screen.
Home screen display value
522KHZ
520KHZ
Select the AM frequency range you need and stop the operation. It will automatically exit the settings and automatically default to the
last selected frequency setting value.
Note: In North American and South American countries such as the United States, Canada, and Mexico, the AM step value is adjusted to
10KHZ, and in other countries it is adjusted to 9KHZ.
7.3.4 Multiple channel search methods are supported
Push-button manual tuning, push-button automatic search for stations , push-button fully automatic search and storage of stations ,
and rotary shuttle button for frequency selection.
7.3.4.1 Push-button manual channel adjustment
Press the [
or
] key lightly to increase or decrease the default value of each band.
FM frequency modulation minimum step value: 0.1MHZ, VHF very high frequency minimum step value: 0.0125MHZ
MW medium wave minimum step value: 9KHZ / 10KHZ UHF ultra high frequency minimum step value: 0.0125MHZ
LW long wave minimum step value: 9KHZ AIR aviation band maximum step value: 0.025MHZ
CB city band minimum step value: 0.005MHZ
When the demodulation mode of SW short wave is AM, the minimum step value is: 0.005MHZ
When the demodulation mode of SW short wave is LSB, the minimum step value is: 0.001MHZ
When the demodulation mode of SW short wave is USB, the minimum step value is: 0.001MHZ
7.3.4.2 Push-button automatic search for radio stations
Press and hold the [
or
value. If a radio station with a signal is found, it will stop searching and play.
7.3.4.3 Button-type automatic search for radio stations
In the radio mode, press and hold the [
save the station.
During the fully automatic scanning and search process, the main LCD screen displays the characters "PRESET" and flashes to search
for radio stations with signals. The main LCD screen displays the characters "CH***", which represents the address number of the
station.
After completing a round of search, the search will automatically stop and the first frequency program stored will be played.
The number of stations that can be stored in each band: 200, the total number of stations that can be stored: 1600 (except for the WB
North American weather band)
Warm reminder: The amount of money stored in the radio station depends on the strength of the local signal.
7.3.4.4 Rotate the shuttle button to select frequency
In the radio working mode, the station can be selected by rotating the inner and outer buttons of the front pulley of the machine.
Enable the small and large shuttle button to select channels according to the step value. The steps are as follows:
Press the inner wheel button lightly
value, rotate the large shuttle button [
frequency point.
The STEP values that can be adjusted in each band are as follows:
] button , and the main screen will display: 64.0MHZ. Press the [
The default working frequency band is
FM1: 64-108MHZ
FM2: 76-108MHZ
FM3: 87.5-108MHZ
] button, and the main screen will display 520KHZ. Press the [
The default working frequency band is
522-1710KHZ
520-1710KHZ
] key for 2 seconds, and each band will quickly search for radio stations according to the default step
] key for 2 seconds to enter the fully automatic scanning station search and automatically
, and the STEP value changes. Press the button
] , and press the selected step value clockwise or counterclockwise to select the required
08
] button
] button
The medium wave step value defaults to
9KHZ
10KHZ
each time to select the required step
Publicidad
