Publicidad
Idiomas disponibles
Idiomas disponibles
• To get long straight lines, it is advisable to stretch
guide strings.
9.1.2
Pruned hedges
It is advisable to cut hedges in a trapezoidal shape to pre-
vent the lower branches from becoming bare. This corre-
sponds to natural plant growth and allows hedges to
thrive. When pruning, only the new annual shoots are re-
duced, so that a dense branching and a good screen is
formed.
• Trim the sides of a hedge first. To do this, move the
product with the direction of growth from bottom to
top. If you cut from the top down, thinner branches
move outwards and this can create thin spots or
holes.
• Then cut the top edge straight, roof-shaped or round,
depending on your taste.
• Trim even young plants to the desired shape. The
main shoot should remain undamaged until the hedge
has reached the planned height. All other shoots are
cut in half.
9.1.3
Cut at the right time
• Leaf hedge: June and October
• Conifer hedge: April and August
• Fast growing hedge: around every 6 weeks from May
Pay attention to nesting birds in the hedge. Delay the
hedge cut or leave this area out if this is the case.
9.2
After use
• Always switch the product off before placing it
down and wait until the product has come to a
standstill.
• Remove the battery.
• Put on the supplied blade guard after each instance of
working with the product.
• Allow the product to cool.
10 Cleaning
WARNING
Have maintenance and repair tasks that are
not described in this operating manual, car-
ried out by a specialist workshop. Use only
original spare parts.
There is a risk of accident! Always perform
maintenance and cleaning work with the bat-
tery removed. There is a danger of injury! Let
the product cool down before all mainte-
nance and cleaning tasks. Elements of the
engine are hot. There is a danger of injury
and burning!
The product can start unexpectedly and cause injuries.
–
Remove the battery.
–
Allow the product to cool down.
–
Remove the tool attachment.
1. Wait until all moving parts have come to a standstill.
2. We recommend that you clean the product directly af-
ter every use.
24 | GB
3. Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasp-
ing surfaces do not allow for safe handling and control
of the tool in unexpected situations.
4. If necessary, clean the handles with a damp cloth*
washed in soapy water.
5. Never immerse the product in water or other liquids
for cleaning.
6. Do not splash the product with water.
7. Keep protective devices, air vents and the motor
housing as free of dust and dirt as possible. Rub the
product clean with a clean cloth* or blow it off with
compressed air* at low pressure. We recommend that
you clean the product directly after every use.
8. Ventilation openings must always be free.
9. Do not use any cleaning products or solvents; they
could attack the plastic parts of the product. Make
sure that no water can penetrate the product interior.
10.1
Hedge trimmer
1. Clean the cutter bar with an oily cloth after each use.
2. Oil the cutter bar after each use with the oil can or a
spray.
11 Maintenance
WARNING
Have maintenance and repair tasks that are
not described in this operating manual, car-
ried out by a specialist workshop. Use only
original spare parts.
There is a risk of accident! Always perform
maintenance and cleaning work with the bat-
tery removed. There is a danger of injury! Let
the product cool down before all mainte-
nance and cleaning tasks. Elements of the
engine are hot. There is a danger of injury
and burning!
The product can start unexpectedly and cause injuries.
–
Remove the battery.
–
Allow the product to cool down.
–
Remove the tool attachment.
• Check the product for obvious defects such as loose,
worn or damaged parts before each use.
• Check the covers and protective devices for damage
and correct seating. Replace them if necessary.
• Regular, careful servicing is required to guarantee the
safety level and performance of the product.
• Position the Product on a straight, level surface.
• Do not splash the product with water.
• For safety reasons, replace worn or damaged parts.
• Any work not described in this operating manual must
be performed by an authorised specialist workshop
only.
www.scheppach.com
Publicidad
