Publicidad
Idiomas disponibles
Idiomas disponibles
STEPS TO FOLLOW TO REALI SE A CUTTI N G
1 Lift slight ly t he blades safeguard t o save height of t he flange and t hen drag it com plet ely left war ds Fig.6
before you can lift it t ot ally.
2 Rest ing t he bars upon t he roller so t hat you can easily m ove t he bar forward as per t he pr edet er m ined
m easurem ent . Place t he bar in t he t hroat bet w een t he t wo blades. Lower back t he blades safeguard and pus hit
right ward t o fr ee t he pedal ( t he m echanism t hat operat es t he cut t ing) .
N ot e : CEL m odels are equipped wit h a safet y sy st em t hat when t he blades safeguard is lift ed, t he blades would not
be able t o cut t he m at er ial.
3 Once t he safeguard has been released, w e can effect uat e a cut t ing, eit her by pressing t he pedal or pulling
t he gr ip.
N e ve r t r y t o m a k e a cu t w h ile t h e sa fe gu a r d is lift e d a s t h e m a t e r ia l t o cu t ca n le a ve t h e cu t t in g t h r oa t a n d
ca u se da m a ge .
5 . SOLUTI ON S TO M OST FREQUEN T AN OM ALI ES
AN OM ALY
Mot or does not st art
Mot or st art s v ery slow ly and t akes t oo
long t o reach it s revolut ions
Cut t ing power is t oo low
Prem at ur e wearing of t he belt s
6 . ELECTRI CAL CON N ECTI ON
The ex t ension cable used t o feed t he m achine needs t o have a m inim um sect ion of 4x2.5 m m
m et ers long. For a superior dist ance 4x4 m m
norm alised aer ial of 3P+ T or 3P+ N+ T com pat ible w it h t he m achine sw it ch and in t he ot her end, one norm alised aer ial
pin of 3P+ T ó 3P+ N+ T com pat ible w it h sw it chboard ex it .
M a ch in e s w it h e le ct r ica l m ot or sh ou ld a lw a ys be con n e ct e d t o a n or m a lise d sw it ch boa r d t h a t dispose s of a
m a gn e t o- t h e r m a l sw it ch a n d a diffe r e n t ia l in a ccor da n ce w it h t h e ch a r a ct e r ist ics of t h e m ot or :
3Kw / 4 CV, t hr ee phase at 400V, 15A m agnet o- t herm al and 15A/ 30m A different ial.
4Kw / 5.5 CV, t hree phase at 400V, 10A m agnet o- t her m al and 10A/ 30m A different ial.
The m achine elect r ical t ension is visible on t he volt age indicat ion nex t t o t he t op of engine t erm inals and on t he
m achine char act er ist ics plat e.
W ARN I N G: D o n ot plu g t h e m a ch in e t o t h e e le ct r icit y if you a r e n ot su r e of t h e a va ila ble e le ct r ica l t e n sion .
I f t h e t e n sion is n ot cor r e ct , t h e e n gin e w ill u n de r go ir r e pa r a ble h a r m or ou t of se r vice .
W ARN I N G: N e ve r m a n ipu la t e t h e pow e r ca ble s or a n y e le ct r ica l e qu ipm e n t of t h e m a ch in e , if you h a ve n ot
t ot a lly u n plu gge d t h e m a ch in e fr om t h e e le ct r icit y.
Once you have brought t he rot at ion direct ion of t he engine back, t he m achine is ready t o operat e.
POSSI BLE CAUSE
Fault of t he elect rical power supply
act ivat ion of t he t herm al prot ect ion of
t he single- phase sw it ch
Swit ch dam aged
Condenser dam aged.
( Single- phase m ot ors)
Belt loose or blunt
Blades blunt
Power drop down of t he m ot or
The belt s slide over t he pulley s
2
can be used. I n one of it s ends, it is needed t o connect a base
7-
SOLUTI ON
Check t he pow er supply in t he swit ch
board. Check the position of the circuit
breaker and the residual current device
in the switch board.
Make sure the extension cable is in good
state and its fitting in the two extremes is
correct.
Wait unt il t he m ot or has cooled dow n
and re- act ivat e t he t her m al prot ect ion
Replace it
Replace it
Tight en t he belt or replace it
Change t he cut t ing face of t he blade
or replace it
Let t he t echnical service check t he
m ot or.
Tight en t he belt s
2
up t o 25
EN GLI SH
Publicidad
