Publicidad
Idiomas disponibles
Idiomas disponibles
3.4) Operation
Activate the pump by pushing the green button on the control handle or the button on the
bar
pump (if enabled), the display (3) and the CEMBRE logo (8) turn-on.
bar
Through the display, the operator can view and change some of the pump's setting using the
touch button (4) (Ref. to § 4). The display shows the operating mode and oil release settings of
the pump at each start-up (starting with the display switched off ) or upon insertion of the bat
psi
tery.
psi
P
= 700 bar
n
P =
0 bar
Examples:
P
= 700 bar
n
P
= 701 bar
IMPORTANT: Prior to using the pump, always check the operating mode set is the correct
p
one for the type of job to be carried out, choosing between:
CRIMPING – CUTTING – PUNCHING (Ref. to § 4.2).
P
= 700 bar
n
OK
Lorem ipsum
ERCH OFF
The factory settings are:
P
= 729 bar
n
1
- operating mode: CRIMPING (Ref. to § 4.2 to choose another operating mode).
*
P =
0 bar
- oil release type: SMART (Ref. to § 4.3 for further details).
P = 0 bar
um
- control: ERCH ON (by remote controller, ref. to § 4.4 for further details).
P
= 10573 psi
n
2
*
P =
0 psi
Proceed with the job by operating as follows:
P
= 325 bar
p
10
90
3
CRIMPING OPERATION
BATTERY
Press the start button: this activates the motor of the pump that feeds the
MP
3
hydraulic head connected to it, pressurising the oil.
EMPTY
4
BATTERY
Once the minimum set pressure (P
off automatically, the display will briefly show the maximum pressure reached
(P
) followed by "OK" and the CEMBRE logo will light up GREEN to confirm the
p
5
90°
*
correct operation.
BATTERY
Releasing the start button before the automatic stopping of the motor will
cause the pump to stop, keeping the oil pressure stable (P
Lorem ipsum
10
2
at that moment. To complete the operation press the start button once more
6
*
-29990
until the motor stops automatically.
rem ipsum
The display "ERROR" combined with a beep and and the RED flashing of
B68MP
7
*
the CEMBRE logo, indicates an incorrect crimping procedure; the oil
NR 16AW125
Lorem ipsum
return phase occurred too early without waiting for the motor to be
automatically switched off and therefore the minimum set pressure was not
LED
8
reached. This error appears when the pressure release button has been operated
ON
and the pump has already reached a pressure > 100 bar. Repeat the crimping cycle
by holding down the start button until the motor is automatically switched off.
60°
9
*
13
max 90°
P
= 700 bar
n
P =
0 bar
P
= 700 bar
n
P
= 701 bar
p
P
= 700 bar
n
OK
P = 0 bar
P =
0 bar
P
= 325 bar
p
P
= 547 bar
p
BATTERY
EMPTY
P
= 700 bar
n
1
*
BATTERY
P =
0 bar
P
= 10153 psi
n
2
*
P =
0 psi
ERCH ON
Lorem ipsum
ERCH OFF
3
4
Lorem ipsum
P
= 700 bar
n
P =
0 bar
ERCH ON
5
LED
P
= 700 bar
n
OFF
P
= 701 bar
p
6
*
BATTERY
P
= 700 bar
n
OK
10
7
*
-29990
P
= 700 bar
n
P =
0 bar
P
= 700 bar
n
P
= 701 bar
p
BATTERY
P
= 700 bar
n
OK
BATTERY
P = 0 bar
30001
BATTERY
P =
0 bar
P
= 325 bar
BATTERY
p
RESET
SW:S1J41405
RESET
P
= 547 bar
p
SW:S1J41405
90°
BATTERY
max 90°
EMPTY
BATTERY
max.
BATTERY
LED
max.
ON
LED
ERCH ON
OFF
BATTERY
BATTERY
) is reached the pump will be switched
n
Lorem ipsum
ERCH OFF
Lorem ipsum
) at the value reached
p
Lorem ipsum
ERCH OFF
BEEP
BATTERY
ERROR
BATTERY
NTC
FAULT
30001
BATTERY
P =
0 bar
BATTERY
001
RESET
ERROR
SW:S1J41405
002
P
= 547 bar
p
RESET
001
P
= 729 bar
n
SW:S1J41405
90°
30001
P =
0 bar
002
003
max 90°
003
P
= 729 bar
004
004
90°
n
P
= 731 bar
max 90°
p
BATTERY
LED
max.
P
= 729 bar
ON
n
min.
ERCH ON
OK
LED
OFF
BATTERY
BATTERY
LED
min.
OFF
ERCH OFF
Lorem ipsum
LED
P = 0 bar
P =
ON
BEEP
ERCH OFF
P
= 325 bar
P
p
p
BEEP
ERCH ON
BEEP
BATTERY
BATTERY
30001
BATTERY
BATTERY
BATTERY
BATTERY
ERROR
NTC
30001
BATTERY
FAULT
BATTERY
001
RESET
ERROR
SW:S1J41405
002
90°
SW:S1J41405
001
30001
002
max 90°
003
003
004
004
90°
max 90°
LED
max.
ON
max.
min.
LED
OFF
BATTERY
BATTERY
LED
min.
OFF
Lorem ips
LED
ON
BEEP
P
= 700 bar
n
BATTERY
P =
0 bar
ERCH OFF
0 bar
P
= 700 bar
n
BEEP
P
= 701 bar
p
ERCH ON
= 547 bar
P
= 700 bar
n
OK
BEEP
P = 0 bar
P =
LED
ERROR
P
= 325 bar
ON
P
p
p
NTC
LED
FAULT
OFF
BATTERY
001
ERROR
EMPTY
BATTERY
002
001
3000
RESET
90°
max 9
BA
max.
BATTERY
m
BA
BATT
BEEP
R
S
= 54
Publicidad
