Publicidad
Idiomas disponibles
Idiomas disponibles
*
When a crimping head is used, press and hold the operating button until the motor stops auto-
matically.
*
At the end of the cycle, proceed with the phase of returning the oil to the pump reservoir (Ref.
to § 3.5 for further details).
CUTTING OPERATION
P
= 700 bar
n
1
P
= 729 bar
Press the start button: this activates the motor of the pump that feeds the
*
P =
n
0 bar
P =
0 bar
hydraulic head connected to it, pressurising the oil. Keep the button pressed
until the cutting operation is complete. At the end of the cycle the display will
P
= 10153 psi
show the maximum pressure reached (P
n
2
*
P
= 729 bar
P =
0 psi
n
At the end of the cycle, proceed with the phase of returning the oil to the
P
= 731 bar
p
pump reservoir (Ref. to § 3.5 for further details).
3
P
= 729 bar
n
PUNCHING OPERATION
OK
*
Press the start button: this activates the motor of the pump that feeds the
4
hydraulic head connected to it, pressurising the oil. Keep the button pressed
P = 0 bar
*
until the punching operation is complete. At the end of the cycle the display
will show the maximum pressure reached (P
At the end of the cycle, proceed with the phase of returning the oil to the pump
ERCH ON
5
P
= 325 bar
p
reservoir (Ref. to § 3.5 for further details).
*
LED
OFF
3.5) Oil release
6
The phase of returning the oil to the pump reservoir, or rather to the re-entry of the ram of the
*
BATTERY
*
connected hydraulic head, may be carried out in two different ways depending on the release
mode set (Ref. to § 4.3 for further details):
10
7
*
With the ERCH remote controller:
-29990
10
- smart mode: release the GREEN start button (following automatic shut-off of the motor).
- manual mode: press the RED release button.
B70MP
8
*
19AB863
With the rocker switch (11) on the pump (only if the remote controller is
11
deactivated):
- smart mode: release the control button at the end of the cycle.
60°
9
*
- manual mode: push the control button backwards.
max 90°
If required, by pressing hard on the mechanical pressure release
button (7), the oil will return to the reservoir whatever the status
RESET
10
of the battery.
SW: S1K25102
11
P
= 700 bar
n
1
P
= 729 bar
P =
0 bar
n
P =
P
= 10153 psi
n
2
P
= 729 bar
P =
0 psi
n
P
= 731 bar
p
3
P
n
OK
4
P = 0 bar
ERCH ON
5
P
p
6
BATTERY
P =
0 bar
10
7
-29990
Lorem ipsum
ERCH OFF
P
= 547 bar
B70MP
p
8
19AB863
60°
9
max 90°
RESET
SW: S1K25102
0 bar
= 729 bar
BATTERY
P =
0 bar
).
p
Lorem ipsum
BATTERY
ERCH OFF
= 325 bar
P
= 547 bar
p
30001
RESET
SW:S1J41405
90°
).
p
max 90°
max.
BATTERY
LED
ON
LED
OFF
Lorem ipsum
BEEP
P
P =
BATTERY
P
BATTERY
P
P
P
= 700 bar
n
RESET
P =
0 bar
SW:S1J41405
ERROR
P
= 700 bar
n
P
= 701 bar
p
001
P
= 700 bar
n
002
OK
BATTERY
max.
003
P = 0 bar
BATTERY
004
LED
ON
P
= 325 bar
p
LED
OFF
BATTERY
min.
Lorem ipsum
EMPTY
BATTERY
BATTERY
LED
OFF
LED
ON
BEEP
Lorem ipsum
7
= 700 bar
n
0 bar
ER
= 700 bar
n
= 701 bar
p
= 700 bar
30001
n
OK
P =
P = 0 bar
90°
max 90°
P
= 325 bar
P
=
p
p
min.
EMPTY
P =
0 bar
BATTERY
BATTERY
P
= 547 bar
p
BEEP
Lorem ipsum
ERCH
BEEP
ERCH
14
Publicidad
