Optional Accessories; Ec Declaration Of Conformity - Makita 4131 Manual De Instrucciones

Inspecting saw blade
• Check the blade carefully for cracks or damage before
and after each use. Replace a cracked or damaged
blade immediately.
• Continuing to use a dull blade may cause a dangerous
kickback and/or motor overload. Replace with a new
blade as soon as it no longer cuts effectively.
• Carbide-tipped saw blades for metal cutter cannot
be re-sharpened.
Replacing carbon brushes (Fig. 15 & 16)
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
Carbide-Tipped Metal Blades for Many Applications
METAL SHEET
Size (mm)
t=1.5 t=3.0
185x36T
185x38T
185x48T
185x70T
005705
CAUTION:
• Always use carbide-tipped saw blades appropriate for
your job. Do not cut aluminum, wood, plastics, con-
crete, tiles, etc.
• Carbide-tipped saw blades for metal cutting saw are
not to be re-sharpened.
Noise
The typical A-weighted noise level determined according
to EN62841:
Sound pressure level (
Sound power level (
Uncertainty (K): 3 dB (A)
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN62841:
Work mode: cutting metal
Vibration emission (a
Uncertainty (K): 1.5 m/s
C-STUD ANGLE-STUD
50x100 45x90 50x50
t=1.6 t=3.2 t=4
): 102 dB (A)
L
pA
): 113 dB (A)
L
WA
2
): 2.5 m/s or less
h, M
2

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Rip fence (Guide rule)
• Safety goggle
• Recommended Carbide-tipped saw blades & work-
piece ranges
NOTE:
• Some items in the list may be included in the tool pack-
age as standard accessories. They may differ from
country to country.
Applications
METAL STUD
50x50 t=0.56 t=1.6
t=6 25Ga 16Ga
Excellent
• The declared vibration emission value has been mea-
sured in accordance with the standard test method and
may be used for comparing one tool with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
ENG905-1
• The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the oper-
ator that are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to
the trigger time).
ENG900-1

EC DECLARATION OF CONFORMITY

For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
REBAR PIPE
∅25 ∅60
50x100
∅20
t=3.2 t=1.2 t=3.8
Good Fair
CORRUGATED
SHEET
t=1.0-
t=0-0.9
2.0
Not Applicable
ENG901-1
9