Rear Panel - Fender BASSBREAKER 18 Manual De Instrucciones

POST
INPUT POWER
POST
INPUT POWER
120V 60Hz
POWER AMP
120V 60Hz
POWER AMP
175W LINE OUT
TBDW
LINE OUT
FUSE
F3A L
250V
J. IEC POWER INLET: Using the included power cord, connect
to a grounded outlet in accordance with the INPUT POWER
voltage and frequency specified at the power inlet.
K. FUSE: Provides electrical over-current protection. With power
disconnected, replace a blown fuse only with one of the type
and rating specified on the amp's rear panel.
L. POST POWER AMP LINE OUT: Provides a line-level signal
(with tone shaping from the channel in use). Power amp
distortion, if any, can be sent to effects devices such as delay
or chorus units and to the effects loop or power amp input of
another amplifier (signal can also be sent to external recording
interfaces and sound reinforcement equipment; note that this
offers no speaker emulation).
M. PARALLEL SPEAKER OUTPUTS: Connect external speaker
enclosures here. To use internal speakers in combination with
an external speaker enclosure, plug external enclosure into
EXTENSION SPEAKER. To use an external speaker cabinet only,
plug external enclosure into MAIN SPEAKER (internal speakers
will automatically be disconnected). See table at right for ac-
ceptable parallel speaker enclosure impedance combinations
for Bassbreaker 18/30.
N. IMPEDANCE SELECT: If no external enclosures are connected
to PARALLEL SPEAKER OUTPUTS (M), this switch should be set
at the 16Ω position. To avoid damage when using PARALLEL
SPEAKER OUTPUTS, this switch must be set in accordance with
total impedance load as shown in the table at right.
O. FOOTSWITCH: Connect included channel-switching single-
button footswitch here.
TYPE
POWER
INPUT IMPEDANCE
SPEAKERS (INTERNAL)
EXTERNAL SPEAKER ENCLOSURE
TUBES
POST POWER AMP LINE OUT
ACCESSORIES
DIMENSIONS
WEIGHT

Rear Panel

PARALLEL
SPEAKER OUTPUTS
PARALLEL
30 WATTS 4Ω min TOTAL
SPEAKER OUTPUTS
MAIN EXTENSION 4Ω - 8Ω -16Ω
MAIN EXTENSION 4Ω - 8Ω -16Ω
SPEAKER SPEAKER IMPEDANCE
SPEAKER SPEAKER IMPEDANCE
SELECT
30WATTS 4Ω min TOTAL MUTES SELECT
INTERNAL
SPEAKER
Specifications
PR 3036
Requirements: 175 watts
1MΩ
Two 12" Celestion® G12V-70 (8Ω each, 16Ω total)
Bassbreaker BB-212 (optional, PN 226800000, contains same speakers as combo model)
V1-2: 7025/12AX7A/ECC83
Output impedance: 82Ω
Single-button footswitch (included, PN 7706424000)
Width: 26.25" (66.7 cm)
50 lbs. (22.7 kg)
Product specifications subject to change without notice.
BASSBREAKER 18/30
B A S S B R E A K E R 1 8 / 3 0
FENDER MUSICAL INSTRUMENTS CORP.,
FENDER MUSICAL INSTRUMENTS CORP.,
SWITCH
SWITCH
Acceptable parallel speaker enclosure impedance combinations
for the Bassbreaker 18/30, with correct IMPEDANCE SELECT
switch (N) settings:
INTERNAL SPEAKER MAIN SPEAKER EXTENSION SPEAKER IMPEDANCE SELECT
16Ω NONE
16Ω NONE
16Ω NONE
DISCONNECTED* 16Ω
DISCONNECTED* 8Ω
DISCONNECTED* 4Ω
DISCONNECTED* 16Ω
DISCONNECTED* 16Ω
DISCONNECTED* 8Ω
*NOTE: When a plug is inserted into MAIN SPEAKER jack, internal speaker load (16Ω)
is automatically disconnected and does not affect total impedance load.
To avoid damaging the amp, put it in STANDBY mode (H)
!
or turn it off (I) when changing speaker connections and
IMPEDANCE SELECT switch (N) settings.
For questions and troubleshooting, contact a Fender
specialist at:
1-800-856-9801 (U.S. toll free)
1-480-596-7195 (International)
Output: 18 watts/30 watts into 16Ω/8Ω/4Ω
V3-6: 6BQ5/EL84
Cover (included, PN 7707569000)
Height: 21.875" (55.6 cm)
TM
TM
A PRODUCT OF:
A PRODUCT OF:
CORONA, CA U.S.A.
CORONA, CA U.S.A. MADE IN MEXICO
MADE IN MEXICO
FOOT
FOOT
NONE 16Ω
16Ω 8Ω
8Ω 4Ω
NONE 16Ω
NONE 8Ω
NONE 4Ω
16Ω 8Ω
8Ω 4Ω
8Ω 4Ω
Depth: 10" (25.4 cm)
3