Serial Numbers - Peg-Perego book pop-up Instrucciones De Uso

_ Chassis book Pop-Up : basket; 2 rear wheels
with brake gear, rear wheel bar, 2 front
wheels, solid handle.
INSTRUCTIONS
1 OPENING: Before opening the frame, remove
(without using blades) any die-cut cardboard.
Press down the side fastener, hold the upper
section of the handle and rotate it towards
you until the frame is fully opened (fig_a).
Open frame (fig_b).
The frame is properly opened when the
attachment on the base clicks into place,
as shown. CAUTION: When placing the seat
on the frame, press the seat downwards to
ensure it engages securely onto the base.
2 FITTING THE WHEELS: Slot the uprights into
the rear wheel crosspiece (fig_a), ensuring
that it is facing the right way, then push the
rear wheels on and make sure that they click
into place (fig_b). To mount the front wheels,
fit them into the uprights until they lock into
place (fig_c).
3 ATTACHING THE MAIN HANDLE: if the handle
tube faces upwards, align it with the stroller
(Fig_a).
Fasten the handle to the frame as shown in
the figure (Fig_b).
To complete the operation, press the two side
buttons on the handle (Fig_c) to ensure the
handle pushes in all the way, until it clicks
into place (Fig_d).
4 FITTING THE BASKET: if lowered, lift the basket
tube to the horizontal position. Press the silver
buttons under the metal basket tube located at
the back of the stroller (fig_a) and remove the
metal tube (fig_b). Thread the tube through the
fabric loop on the back of the basket, making
sure that the two silver buttons are facing
downward (fig_c). Re-attach the tube to the
housings (fig_d).
5 Secure the two upper basket vinyl eyelets to the
two grey buttons on either side of the metal tube
housing. Please note that the eyelets open (fig_e).
Remove the cardboard from the lower rear bar.
IMPORTANT! Secure the two lower basket vinyl
eyelets to the two grey buttons on the top of the
lower rear bar. Please note that the eyelets open
(fig_f).
WARNING! If this operation is not performed
correctly, the basket will not properly hold the
weight.
Attach the basket tabs to the grey buttons on the
front of the frame (figure).
REFER TO OUR INSTALLATION INSTRUCTIONS
VIDEO AT:
WWW.PEGPEREGO.COM
6 FIXED OR SWIVEL FRONT WHEELS: to fix
the front wheels, rotate the lever counter
clockwise to the locked padlock (fig_a); to
release the wheels, turn the lever clockwise
to the unlocked padlock (fig_b). On difficult
terrain, we recommend using fixed wheels.
7 BRAKE: Press the lever down to apply the
brake on the chassis and lift it to release the
brake.
8 ADJUSTABLE HANDLEBAR: To adjust the
height of the handlebar, press both of the
side buttons at the same time (fig_a) and
swing it into the desired position (fig_b), then
release the buttons.
9 FOLDING UP: The chassis can be folded up
without the seat, with the seat facing the
person pushing (recline the backrest before
folding it) or with the seat facing forward.
To fold the stroller, it is best to set the front
wheels to their fixed position and close the
hood (if fitted). Place the handle as shown in
the figure (fig_a).
Pull the inside handle on the base (fig_b) and
lift it (fig_c); the handle will drop forward
until the frame is closed.
1 0 To ensure the frame is closed properly, check
that the side fastener is enabled (fig_a). When
closed, the frame remains in the upright
position (fig_b).
1 1 For greater compactness, it is possible to
remove the wheels.
To remove the rear wheels: pull the pivot
outwards and remove the wheel as shown in
the figure (fig_a).
To remove the front wheels: press the tab as
shown, and remove the wheel (fig_b).
TRANSPORT: the stroller can be carried
comfortably locking the front wheels and
grasping the main handle (fig_c).
GANCIOMATIC SYSTEM
1 2 Ganciomatic is a fast and practical system
that allows you to attach the Bassinet
Pop-Up,the Primo Viaggio car seat or the
Seggiolino Switch/ Seggiolino Pop-Up seat
to the Ganciomatic Base of the chassis in one
quick step.
Place the item on the Ganciomatic Base and
press down with both hands until it clicks
into place.
Always apply the chassis or stroller brake
before attaching and removing products
(refer to the respective instruction manuals).
Check that the child transport unit is properly
attached.

SERIAL NUMBERS

1 3 Information about the production date can
be found on the Chassis book Pop-Up .
_ The product name, production date and serial
number of the chassis.
This information is required for any
complaints.
- 19 -