Optional Accessories - Makita VC1310L Manual De Instrucciones

CAUTION:
• Do not apply a great impact on the powder filter and
tank. Applying a great impact may cause deformation
and damage to powder filter and tank.
• Empty the tank at least once a day although this
depends on picked-up dust volume in the tank. Or, the
suction force will weaken and the motor may be
broken.
• Do not grab the hook when emptying the tank.
Grabbing the hook may cause the hook to break.
Unhook and lift up the tank cover. (Fig. 26)
Shake off the dust from powder filter, damper and prefilter
and then take the polyethylene bag out of the tank.
(Fig. 27)
NOTE:
• Take the polyethylene bag carefully out of the tank so
that the polyethylene bag cannot be caught and torn by
the protrusion inside the tank when emptying it.
• Empty the polyethylene bag before it becomes full. Too
much dust in the tank may cause the polyethylene bag
to be torn.
Installing powder filter (Fig. 11)
Place the prefilter in the tank.
Next, mount the damper on the powder filter and then
place it in the prefilter.
When installing powder filter and prefilter, the mounting
position marking on each of them are aligned with that
one at the top of the tank.
Finally, mount the tank cover.
NOTE:
• Models VC2510L and VC3210L have no mounting
position marking and no need to align it.
• Before using the powder filter, make sure that prefilter
and damper are always used together. It is not allowed
to install powder filter solely.
• Before using the paper pack, make sure that powder
filter, damper and prefilter are always used together.
Carrying the cleaner (Fig. 28)
When carrying the cleaner, carry it by holding the handle
on the head as shown in the figure. The handle is
retractable at the head when not in use.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
Storage of power supply cord
For Model VC1310L only (Fig. 29 & 30)
Pull out the cord hook or open the base hook. Wind up the
power supply cord and hang it on the cord hook or wind it
around the base hook.
NOTE:
• Do not force the power supply cord off the cord hook
when trying to disconnect it from there. Forcing power
supply cord to disconnect from the cord hook may
cause damage to the cord.
12
For Models VC2510L and VC3210L (Fig. 31 & 32)
Wind up the power supply cord around the base hook.
Storage of accessories
NOTE:
• Do not apply an excessive force to the accessories that
are held by the pipe holder. Applying an excessive
force to these accessories may cause damage to the
pipe holder.
For Model VC1310L only (Fig. 33)
Pipe holder can be used to store straight pipe, bent pipe,
corner nozzle and similars by just inserting these
accessories.
The pipes can be placed into the pipe holder when also
stopping using the cleaner on the way for a while.
(Fig. 34)
For Models VC2510L and VC3210L (Fig. 35)
Pipe rest can be used to store straight pipe, bent pipe and
others by just inserting these accessories. (Fig. 36)
The pipes can be placed into the pipe holder when also
stopping using the cleaner on the way for a while.
Cleaning
CAUTION:
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Clogged powder filter, prefilter and damper cause poor
suction performance. (Fig. 37)
Clean out the filters and dampers from time to time.
To remove dust or particles adhering to the filters, shake
the frame bottom quickly several times.
Occasionally wash the powder filter in water, rinse and dry
thoroughly in the shade before use. Never wash filters in a
washing machine. (Fig. 38)
NOTE:
• Do not rub and scratch the powder filter, the prefilter or
the damper with hard objects such as a brush and a
paddle.
• The filters are consumable and are recommended to
have some spares for them.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Hose
• Front cuffs (22, 24, 38)
• Straight pipe
• Corner nozzle
• Round brush
• Powder filter (For dry type)
• Damper