Installing The Water Filter; Optional Accessory - Makita DVC862L Manual De Instrucciones

3. Mount the damper on the powder filter and then
place them in the prefilter with aligning the mounting
position markings.
4. Finally, mount the tank cover and lock it.
► Fig.12: 1. Tank cover 2. Powder filter (HEPA)
3. Damper 4. Prefilter 5. Tank 6. Mounting
position marking
NOTICE:
Before using the powder filter, make
sure that prefilter and damper are always used
together. It is not allowed to install powder filter
solely.

Installing the water filter

Only for cloth filter model (optional accessory)
CAUTION:
Never pick up water or wet dust
without the float and the cloth filter or the water
filter.
CAUTION:
For picking up wet dust, make
sure that the float cage and the float are installed
on the cleaner.
CAUTION:
When installing the water filter on
the tank, set it tight at the opening of the tank so
that the hook of the water filter engages the tank
opening firmly and there is no space between the
water filter and the tank.
To pick up water or wet dust only, the water filter is more
suitable than the cloth filter.
When installing the water filter, align its mounting posi-
tion mark with the one on the tank.
► Fig.13: 1. Water filter 2. Tank 3. Mounting position
marking
NOTE: It is recommended using water filter when
picking up large amount of water repeatedly.
Otherwise vacuum ability may be reduced in case of
cloth filter.
Installing the paper pack

Optional accessory

WARNING:
When using the paper pack, also
use the cloth filter or prefilter together that is
preinstalled on the tool. Failure to use the cloth filter
/ prefilter together may cause unusual noise and heat,
resulting in a fire.
CAUTION:
(For the cloth filter model)
• Never pick up water or other liquids or wet
dusts when using the paper pack. Picking
up such things may cause the paper pack
breakage.
Before using the paper pack, make sure that
•
powder filter (optional accessory), damper
(optional accessory) and prefilter are always
used together.
CAUTION:
(For the powder filter model)
• Before using the paper pack, make sure
that powder filter, damper and prefilter are
always used together.
1. Remove the rubber holder.
► Fig.14: 1. Rubber holder
2. Extend the paper pack.
3. Align the paper pack opening with the dust suction
opening of the cleaner.
4.
Insert the cardboard of the paper pack onto the
holder so that it is positioned at the end beyond the
detent protrusion.
► Fig.15: 1. Paper pack 2. Holder
Installing the polyethylene bag
Cleaner can also be used without polyethylene bag.
However, using polyethylene bag is easier to empty the
tank without letting your hands dirty.
Spread the polyethylene bag in the tank. Insert it
between the holder plate and the tank, and pull it to the
hose inlet.
► Fig.16: 1. Holder plate 2. Polyethylene bag
Spread the bag around the top of the tank so that the
cloth filter / prefilter edge can catch and hold the bag
securely.
► Fig.17: 1. Cloth filter / prefilter
NOTE: A polyethylene bag available on the
market can be used. 0.04 mm or thicker one is
recommended.
NOTE: Too much dust will tear the bag easily, so
do not collect the dust more than the half of the bag
capacity.
Emptying the polyethylene bag
WARNING:
cleaner is switched off and the battery cartridge is
removed before emptying the polyethylene bag.
Failure to do so may cause an electric shock and
serious personal injury.
CAUTION:
Do not apply a great impact on the
float cage and tank. Applying a great impact may
cause deformation and damage to the parts.
CAUTION:
Empty the tank at least once a day
although this depends on picked-up dust volume
in the tank. Or, the suction force will weaken and the
motor may be broken.
CAUTION:
Do not grab the hook when empty-
ing the tank. Grabbing the hook may cause the hook
to break.
Unhook and lift up the tank cover.
Shake off the dust from the cloth filter / prefilter and then
take the polyethylene bag out of the tank.
► Fig.18
NOTE: Take the polyethylene bag carefully out of the
tank so that the polyethylene bag cannot be caught
and torn by the protrusion inside the tank when emp-
tying it.
NOTE: Empty the polyethylene bag before it
becomes full. Too much dust in the tank may cause
the polyethylene bag to be torn.
11 ENGLISH
Always make sure that the