Using Pedals; Effects - Korg C1 Manual De Usuario

ORGAN2 1 Pipe Organ1
2 Pipe Organ2
3 Positive Organ
STRINGS 1 Strings
2 Cinema Strings
3 Choir
BASS& 1 A. Bass/Piano
PIANO
2 E. Bass/E. Piano
3 Bass&Cym/Piano
The # column shows the number of oscillators, or voices,
used to create a single note for that sound. (refer to "About
maximum polyphony" on page 16.)

Using pedals

Soft pedal
Sostenuto pedal
The C1/C1 Air includes all three of the pedals found on a
grand piano. Using the pedals can add expression, control,
and sophistication to any performance.
Soft pedal (left)
The Soft pedal slightly reduces the volume and softens
the tone. Accurate half-pedaling allows you to control the
depth of the effect by how far down the pedal is pressed.
("half-pedaling").
Sostenuto pedal (center)
This pedal provides a similar effect as the Damper ped-
al—allowing notes to continue to sound after the key is
released—but the effect only applies to the notes already
being held down when the Sostenuto pedal is pressed. New
notes played after the Sostenuto pedal has been pressed
will not sustain.
Damper pedal (right)
As mentioned above, the Damper pedal allows notes to
continue to sound after the key has been released, adding
a rich, resonant decay. You can also add the damper reso-
nance to the German Grand Piano, Classic Piano (bank 1
and 3 of PIANO1) and the Japanese Grand Piano (bank 2 of
PIANO2) tone . Accurate half-pedaling allows you to con-
trol the depth of the effect by how far down the pedal is
pressed. ("half-pedaling").
8
2
2
2
2
2
2
4
2
4
Damper pedal

Effects

Brilliance
This effect changes the brightness of the tone.
The setting can be changed by holding down the BRIL-
LIANCE button and pressing the + or – button beside the
display.
The setting appears in the display with 003 producing a
brighter sound and 001 producing a less bright sound.
Brilliance cannot be turned off.
The same setting is applied to all sounds and remains
applied until the C1/C1 Air is turned off. When the in-
strument is turned on, the default setting 002 is selected.
By performing the "Save parameter settings" (see page
13) operation before turned off, the new settings spec-
ified for each sound can be saved as the default settings.
Reverb
This effect adds ambience and depth to the sound, produc-
ing the sense of performing in a concert hall.
Each press of the REVERB button turns the reverb on
(button lights up) or off (button turns off).
To change this setting, hold down the REVERB button
and press the + or – button beside the display.
The setting appears in the display with 003 producing a
deep reverb effect and 001 producing a light reverb effect.
As a factory default, the on/off setting for this effect as
well as this effect's setting are saved with each sound.
By performing the "Save parameter settings" (see page
13) operation before the sound is switched, the new
settings specified for each sound can be saved as the
default settings.
Chorus
Chorus adds modulation to the sound, producing an ex-
pansively rich sound.
Each press of the CHORUS button turns the Chorus effect
on (button lights up) or off (button turns off).
To change this setting, hold down the CHORUS button
and press the + or – button beside the display.
The setting appears in the display with 003 producing a
deep chorus effect and 001 producing a light chorus effect.
As a factory default, the on/off setting for this effect as
well as this effect's setting are saved with each sound.
By performing the "Save parameter settings" (see page
13) operation before the sound is switched, the new
settings specified for each sound can be saved as the
default settings.