Sony WX-GT99BTM Manual De Instrucciones página 33

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

SW DIREC*
(Subwoofer Direct
4
Connection)
SW MODE (Subwoofer Mode)
Selects the subwoofer mode: "1," "2," "3,"
"OFF."
SW PHASE (Subwoofer Phase)
Selects the subwoofer phase: "NORM,"
"REV."
SW POS*
(Subwoofer Position)
1
(page 30)
Selects the subwoofer position: "NEAR,"
"NORMAL," "FAR."
LPF FREQ (Low Pass Filter Frequency)
Selects the subwoofer cut-off frequency:
"50Hz," "60Hz," "80Hz," "100Hz,"
"120Hz."
LPF SLOP (Low Pass Filter Slope)
Selects the LPF slope: "1," "2," "3."
S.WOOFER (Subwoofer)
SW LEVEL (Subwoofer Level)
Adjusts the subwoofer volume level:
"+10 dB" – "0 dB" – "–10 dB."
("ATT" is displayed at the lowest
setting.)
SW PHASE (Subwoofer Phase)
Selects the subwoofer phase: "NORM,"
"REV."
SW POS*
(Subwoofer Position)
1
Selects the subwoofer position: "NEAR,"
"NORMAL," "FAR."
LPF FREQ (Low Pass Filter Frequency)
Selects the subwoofer cut-off frequency:
"50Hz," "60Hz," "80Hz," "100Hz,"
"120Hz."
LPF SLOP (Low Pass Filter Slope)
Selects the LPF slope: "1," "2," "3."
HPF (High Pass Filter)
HPF FREQ (High Pass Filter Frequency)
Selects the front/rear speaker cut-off
frequency: "OFF," "50Hz," "60Hz,"
"80Hz," "100Hz," "120Hz."
HPF SLOP (High Pass Filter Slope)
Selects the HPF slope (effective only
when HPF FREQ is set to other than
"OFF"): "1," "2," "3."
AUX VOL*
(AUX Volume Level)
5
Adjusts the volume level for each
connected auxiliary equipment:
"+18 dB" – "0 dB" – "–8 dB."
This setting negates the need to adjust
the volume level between sources.
BTA VOL*
(Bluetooth Audio Volume
6
Level) (page 26)
*1 Does not appear when "SET F/R POS" is set to
"OFF."
*2 Does not appear when the tuner is selected.
*3 When "SW DIREC" is set to "OFF."
*4 When "RBE MODE" is set to "OFF."
*5 When the AUX is selected.
*6 When Bluetooth audio source is activated.
DISPLAY:
DEMO (Demonstration)
Activates the demonstration: "ON,"
"OFF."
BLK OUT (Black Out)
Turns off the illumination automatically
for any source (e.g., during radio
reception/CD playback, etc.) if no
operation is performed for 5 seconds:
"ON," "OFF."
To turn the light back on, press any
button on the unit or the remote
commander.
DIMMER
Changes the display brightness.
– "AT": to dim the display automatically
when you turn lights on. (Available only
when the illumination control lead is
connected.)
– "ON": to dim the display.
– "OFF": deactivate the dimmer.
COLOR (Preset Color)
Selects the preset color of the display and
buttons on the main unit (page 18).
CUSTOM-C (Custom Color)
Selects a preset color as a basis for
further customizing (page 18).
33

Publicidad

Capítulos

Tabla de contenido

Solución de problemas

loading

Tabla de contenido