Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
check for any damage to the blade or flanges. A cracked or
damaged blade or flange can come apart and pieces can
be thrown at high speeds, causing serious injury.
•
DO NOT use lubricants or cleaners (particularly spray
or aerosol) in the vicinity of the plastic guard. The
polycarbonate material used in the guard is subject to
attack by certain chemicals.
•
ALWAYS USE THE KERF PLATE AND REPLACE THIS
PLATE WHEN DAMAGED. Small chip accumulation
under the saw may interfere with the saw blade or may
cause instability of workpiece when cutting.
•
USE ONLY BLADE FLANGES specified for this tool to
prevent damage to the machine and/or serious injury.
•
CLEAN THE MOTOR AIR SLOTS of chips and sawdust.
Clogged motor air slots can cause the machine to
overheat, damaging the machine and possibly causing a
short which could cause serious injury.
•
KEEP ARMS, HANDS, AND FINGERS away from the
blade to prevent severe cuts. Clamp all workpieces that
would cause your hand to be within 6" (152 mm) of the
saw blade.
•
NEVER LOCK THE SWITCH IN THE "ON" position. Severe
personal injury may result.
•
TURN OFF THE MACHINE and allow the blade to come
to a complete stop before raising the arm and prior to
cleaning the blade area, removing debris in the path of the
blade, before servicing or adjusting tool. A moving blade
can cause serious injury.
PROPERLY SUPPORT LONG OR WIDE WORKPIECES.
•
Loss of control of the workpiece can cause injury.
NEVER cross arms in front of blade while using tool.
•
Always make a dry run (unpowered) before making a
finish cut so that you can check the path of the blade or
severe personal injury may result.
•
NEVER cut workpieces shorter than 1" (30 mm). (Fig. B)
Fig. B
WARNING: Do not connect unit to electrical
power source until complete instructions are read
and understood.
WARNING: Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19)
during use. Under some conditions and duration
of use, noise from this product may contribute to
hearing loss.
WARNING: NEVER MAKE ANY CUT UNLESS THE
MATERIAL IS SECURED ON THE TABLE AND AGAINST
THE FENCE.
WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause cancer,
birth defects or other reproductive harm. Some
examples of these chemicals are:
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
ON MOTOR HOUSING:
WARNING: FOR YOUR OWN SAFETY, READ
INSTRUCTION MANUAL BEFORE OPERATING
SAW.
WHEN SERVICING, USE ONLY IDENTICAL
RE PLACE MENT PARTS.
ALWAYS WEAR EYE PROTECTION.
DO NOT EXPOSE TO RAIN OR USE IN DAMP
LOCATIONS.
ON MOVING FENCE:
ALWAYS ADJUST FENCE PROPERLY BEFORE USE.
Clamp small pieces before cutting. See manual.
ON GUARD:
DANGER – KEEP AWAY FROM
BLADE.
ON UPPER GUARD:
PROPERLY SECURE BRACKET WITH BOTH SCREWS
BEFORE USE.
ON TABLE: (2 PLACES)
WARNING: FOR YOUR OWN SAFETY READ
INSTRUCTION MANUAL BEFORE OPERATING
MITER SAW.
KEEP HANDS OUT OF PATH OF SAW BLADE.
DO NOT OPERATE SAW WITHOUT GUARDS IN
PLACE.
CHECK LOWER GUARD FOR PROPER CLOSING
BEFORE EACH USE.
ALWAYS TIGHTEN ADJUSTMENT BEFORE USE. DO
NOT PERFORM ANY OPERATION FREEHAND.
NEVER REACH IN BACK OF SAW BLADE. NEVER
CROSS ARMS IN FRONT OF BLADE.
TURN OFF TOOL AND WAIT FOR SAW BLADE TO
STOP BEFORE MOVING WORKPIECE, CHANGING
SETTINGS OR MOVING HANDS.
DISCONNECT POWER BEFORE CHANGING BLADE
OR SERVICING.
ENGlIsH
47
Publicidad
Tabla de contenido
