EINHELL TE-ID 650E Manual De Instrucciones página 19

Anleitung TE_ID_650_E_SPK8__ 11.09.12 15:33 Seite 19
7. Operation
Hold the tool by the insulated handles when
carrying out work during which the plug-in tool
could strike concealed power cables or its own
mains lead. Contact with a live cable will also make
the metal parts of the tool live and will cause an
electric shock.
7.1 ON/OFF switch (Fig. 8/Item 5)
First fit a suitable drill bit into the tool (see 6.4).
n
Connect the mains plug to a suitable socket.
n
Position the drill in the position you wish to drill.
n
To switch on:
Press the ON/OFF switch (5)
Continuous operation:
Secure the ON/OFF switch (5) with the locking button
(4).
To switch off:
Press the ON/OFF switch (5) briefly.
7.2 Adjusting the speed (Fig. 8/Item 5)
You can infinitely vary the speed whilst using the
n
tool.
Select the speed by applying a greater or lesser
n
pressure to the ON/OFF switch (5).
Select the correct speed: The most suitable
n
speed depends on the workpiece, the type of use
and the drill bit used.
Low pressure on the ON/OFF switch (5): Lower
n
speed (suitable for: soft materials)
Greater pressure on the ON/OFF switch (5):
n
Higher speed (suitable for hard materials)
Tip: Start drilling holes at low speed. Then increase
the speed in stages.
Benefits:
The drill bit is easier to control when starting the
n
hole and will not slide away.
You avoid drilling messy holes (for example in
n
tiles).
7.3 Preselecting the speed (Fig. 8/Item 6)
The speed controller (6) enables you to define the
n
maximum speed. The ON/OFF switch (5) can
only be pressed to the defined maximum speed
setting.
Set the speed using the setting ring (6) on the
n
ON/OFF switch (5).
Do not attempt to make this setting whilst the drill
n
is in use.
7.4 Clockwise/Counter-clockwise switch
(Fig. 8/Item 7)
Change switch position only when the drill is
n
at a standstill!
Switch the direction of the hammer drill using the
n
clockwise/counter-clockwise switch (7):
Direction
Clockwise (forwards and drill)
Counter-clockwise (reverse)
7.5 Drill / hammer drill selector switch
(Fig. 9/Item 3)
Change switch position only when the drill is
n
at a standstill!
Drill
Drill / hammer drill selector switch (3) in the drill
position. (Position A)
Use: Wood, metal, plastic
Hammer drill
Drill / hammer drill selector switch (3) in the hammer
drill position. (Position B)
Use: Concrete, rock, masonry
7.6 LED lamp (Fig. 1/Item 11)
The LED lamp (11) can be used to additionally
illuminate the position you wish to drill. The LED lamp
(11) will be lit as soon as you insert the power plug.
7.7 Tips for working with your hammer drill
7.7.1 Drilling in concrete and masonry
Switch the Drill/Hammer drill selector switch (3) to
n
position B (hammer drill).
Always use carbide drill bits and a high speed
n
setting for drilling into masonry and concrete.
7.7.2 Drilling in steel
Switch the Drill/Hammer drill selector switch (3) to
n
position A (drill).
Always use HSS drill bits (HSS = high speed
n
steel) and a low speed setting for drilling steel.
We recommend that you lubricate the hole with a
n
suitable cutting fluid to prevent unnecessary drill
bit wear.
7.7.3 Starting holes
If you wish to drill a deep hole in a hard material
n
(such as steel), we recommend that you start the
hole with a smaller drill bit.
GB
Switch position
Pushed in to the right
Pushed in to the left
19