Sony HT-CT500 Manual De Instrucciones página 99

Ocultar thumbs Ver también para HT-CT500:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

When the system is in standby mode, there is
no image or sound on the TV.
• When the system is in standby mode, image
and sound are output from the HDMI
component selected the last time you turned
off the system. To enjoy another component,
play the component and perform the One-
Touch Play operation, or turn on the system
to select the HDMI component you want to
enjoy.
• Make sure [HDMI Pass Through] is set to
[ON] in the GUI menu if you connect
components not compatible with the
"BRAVIA" Sync to the system (page 65).
S-AIR function
Sound transmission is not established.
• If you use another S-AIR main unit, place it
more than 8 m (about 25 feet) away from the
system.
• Confirm that the S-AIR IDs of the
subwoofer and the S-AIR sub unit are the
same (page 87).
• Another S-AIR sub unit is paired to the
S-AIR main unit. Pair the desired S-AIR sub
unit with the S-AIR main unit (page 90).
• Place so that the S-AIR main unit and S-AIR
sub unit are separated from other wireless
devices.
• Avoid using any other wireless devices.
• The S-AIR sub unit is turned off. Make sure
the AC power cord (mains lead) is connected
and turn on the S-AIR sub unit.
No sound is heard from the S-AIR product.
• If you use another S-AIR main unit, place it
more than 8 m (about 25 feet) away from the
S-AIR main unit you are using.
• Confirm that the S-AIR IDs of the
subwoofer and the S-AIR sub unit are the
same (page 87).
• Check the pairing setting (page 90).
• Place the S-AIR main unit and S-AIR sub
unit closer together.
• If you are using any equipment that
generates electromagnetic energy such as a
microwave oven near an S-AIR product,
turn off the equipment and try using the
S-AIR product again after waiting for a short
time.
• Avoid using any other wireless devices.
• Change the [RF Change] setting (page 92).
• Change the ID settings of the S-AIR main
unit and S-AIR sub unit.
• Turn off the system and S-AIR sub unit, then
turn them on again.
• The system does not support S-AIR devices
other than S-AIR receivers.
• Wireless surround amplifiers cannot be used
with this system.
There is noise or the sound skips.
• If you use another S-AIR main unit, place it
more than 8 m (about 25 feet) away from the
S-AIR main unit you are using.
• Sources with copyright protection may not
be playable on S-AIR receivers.
• Place the S-AIR main unit and S-AIR sub
unit closer together.
• If you are using any equipment that
generates electromagnetic energy such as a
microwave oven near an S-AIR product,
turn off the equipment and try using the
S-AIR product again after waiting for a short
time.
• Place so that the S-AIR main unit and S-AIR
sub unit are separated from other wireless
devices.
• Avoid using any other wireless devices.
• Change the [RF Change] setting (page 92).
• Change the ID settings of the S-AIR main
unit and S-AIR sub unit.
Other
The remote does not function.
• Make sure that the connectors for the remote
control are connected to each REMOTE
CTRL jack of the subwoofer and the
speaker.
• Point the remote at the remote sensor
the front panel display of the subwoofer or
the speaker.
in
continued
99
US

Publicidad

Tabla de contenido
loading

Tabla de contenido