Adjusting The Milling Depth; Dust Extraction - Festool OF 1010 EQ Manual De Instrucciones

b) Removing the tool
- Turn the spindle until the spindle stop (1.14)
catches when pressed and the spindle is locked
in place.
- Loosen the locking nut (1.13) using a 19 mm
open-ended spanner until a resistance is felt.
Overcome this resistance by turning the open-
ended spanner even further.
- Remove the cutter.
5.3 How to change the clamping collet
Clamping collets are available for following shank
diameters: 6.0 mm, 6.35 mm, 8 mm (order num-
bers see Festool catalogue or Internet „www.
festool.com".
- Fully unscrew the nut (1.13) and remove from
spindle together with the clamping collet.
- Only insert a new clamping collet in the spindle
when the nut is attached and engaged, then
tighten the nut slightly. Do not tighten the nut
until a milling cutter has been fi tted.
5.4

Adjusting the milling depth

The milling depth is adjusted in three stages:
a) Setting the zero point
- Open the clamping lever (1.6) so that the stop
cylinder (1.7) can move freely.
- Place the router with router table (1.11) onto a
smooth surface. Open the rotary knob (1.15) and
press the machine down until the milling cutter
rests on the base.
- Clamp the machine in this position by tightening
the rotary knob (1.15).
- Press the stop cylinder against one of the three
sensing stops of the pivoted turret stop (1.9).
The individual height of each sensing stop can be
adjusted with a screwdriver:
Sensing stop
A
B
C
- Push the pointer (1.4) down so that it shows 0
mm on the scale (1.5).
b) Setting the milling depth
The desired milling depth can be set either with
the quick depth adjustment or with the fi ne depth
adjustment.
• Quick depth adjustment: Pull the stop cylinder
(1.7) up until the pointer shows the desired
milling depth. Clamp the stop cylinder in this
position with the clamping lever (1.6).
• Fine depth adjustment: Clamp the stop cyl-
inder with the clamping lever (1.6). Set the
desired milling depth by turning the adjusting
min. height/max. height
38 mm/44 mm
44 mm/54 mm
54 mm/67 mm
wheel (1.3) in. Turn the adjusting wheel to the
next mark on the scale to adjust the milling
depth by 0.1 mm. One full turn adjusts the
milling depth by 1 mm. The maximum adjust-
ment range with the adjusting wheel is 8 mm.
c) Increasing the milling depth
- Open the rotary knob (1.15) and press the tool
down until the stop cylinder touches the sensing
stops.
- Clamp the machine in this position by tightening
the rotary knob (1.15).
5.5

Dust extraction

Always connect the machine to a dust
extractor. A connection for extracting dust
and chips (1.8) is a standard feature on
the routers.
At the same time a chip guard (2.2) on the side
stop prevents fl ying chips.
With edge routing, the best extraction effect is
obtained with the extractor hood AH-OF, available
as an accessory.
KSF-OF chip catcher
Using the KSF-OF chip catcher (9.1) (sometimes
included in the scope of delivery), the effi ciency
of the extraction can be increased when routing
edges. Installation is similar to that of the copy-
ing ring.
The hood can be cut off along the grooves (9.2)
using a hacksaw and can thus be reduced in size.
The chip catcher can then be used for interior
radiuses up to a minimum radius of 40 mm.
6 Working with the machine
Always secure the workpiece in such a
manner that it cannot move while being
sawed.
The machine must always be held with
both hands by the designated handles
(1.15, 1.17).
You should wear a dust mask for work
which produces dust.
Always advance the router in the direction op-
posite to the direction of rotation of the cutter
(counter-routing)!
When routing (ensure feed direction of power tool
is the same as cutting direction of tool, Fig. 5).
15