Descargar Imprimir esta página

DeWalt DW715 Manual De Instrucciones página 2

Ocultar thumbs Ver también para DW715:

Publicidad

Idiomas disponibles

Idiomas disponibles

f
Definitions:
Safety
Guidelines
The definitions below describe the level of severity for each signal word. Please read the
manual and pay attention to these symbols.
i_,DANGER: Indicates an imminently hazardous situation which, if not avoided, will result
in death or serious injury.
_ WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
A CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result
in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may
result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALTTOOL,
CALL US TOLL FREE AT: 1-800-4-DEWALT
(1-800-433-9258}
IMPORTANT
SAFETY
INSTRUCTIONS
A
WARNING: Read all instructions before operating product. Failure to follow
all.instructions listed below may result in electric shock, fire and/or serious
injury
READ ALL INSTRUCTIONS
Double
Insulation
Double insulated tools are constructed
throughout with two separate layers of electrical
insulation or one single layer of reinforced insulation between you and the tool's electrical
system. Tools built with this insulation system are not intended to be grounded. As a result,
your tool is equipped with a two prong plug which permits you to use extension cords without
concern for maintaining a ground connection.
NOTE: Double insulation does not take the place of normal safety precautions when
operating this tool. The secondary insulation system is for protection against injury resulting
from a possible failure of the primary insulation within the tool.
_CAUTION:
WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. Repair or
replace damaged cords.
Polarized
Plugs
Polarized plugs (one blade is wider than the other) are used on equipment to reduce the risk
of electric shock. When provided, this plug will fit in the polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not change the plug in any way.
Safety
Instructions
For All Tools
AWARNING:
To reduce the risk of eye injury, ALWAYS use eye protection
when
operating the miter saw.
• KEEP GUARD IN PLACE and in working order.
REMOVE ADJUSTING
KEYS AND WRENCHES. Form habit of checking to see that
keys and adjusting wrenches are removed from spindle before turning tool on. Tools, scrap
pieces, and other debris can be thrown at high speed, causing injury.
• KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
DO NOT USE THE MACHINE IN A DANGEROUS ENVIRONMENT.
The use of power
tools in damp or wet locations or in rain can cause shock or electrocution. Keep your work
area well-lit to avoid tripping or placing arms, hands, and fingers in danger.
• KEEP CHILDREN AWAY. All visitors should be kept at a safe distance from work area.
Your shop is a potentially dangerous environment.
• MAKE WORKSHOP
CHILDPROOF
with padlocks, master switches or by removing
starter keys. The unauthorized start-up of a machine by a child or visitor may result in injury.
• DON'T FORCE TOOL. It will do the job better and be safer at the rate for which it was
designed.
• USE RIGHT TOOL. Don't force tool or attachment
to do a job for which it was not
designed. Using the incorrect tool or attachment may result in personal injury.
• WEAR PROPER APPAREL. No loose clothing, gloves, neckties, rings, bracelets or other
jewelry to get caught in moving parts. Non-slip footwear is recommended. Wear protective
hair covering to contain long hair. Air vents may cover moving parts and should also be
avoided.
• ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses. Also
use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY
EQUIPMENT."
• ANSI Z87.1 eye protection (CAN/CSA Z94.3)
• ANSI $12.6 ($3.19) hearing protection
• NIOSH/OSHA/MSHA
respiratory protection
• SECURE THE WORKPIECE.
Use clamps or a vise to hold the workpiece on the table
and against the fence or when your hand will be dangerously close to the blade [within
6" (152 mm)]. It is safer than using your hand and it frees both hands to operate tool
• DON'T OVERREACH. Keep proper footing and balance at all times. Loss of balance may
cause personal injury.
• MAINTAIN
TOOLS WITH CARE. Keep tools sharp and clean for best and safest
performance.
Follow instructions
for lubricating
and changing
accessories.
Poorly
maintained tools and machines can further damage the tool or machine and/or cause
injury.
• TURN THE MACHINE
"OFF"
AND DISCONNECT
THE MACHINE
FROM
THE
POWER SOURCE before installing or removing accessories, before adjusting or changing
set-ups, when making repairs or changing locations. An accidental start-up can cause
injury. Do not touch the plug's metal prongs when unplugging or plugging in the cord.
• REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure that the switch is in
the "OFF" position before plugging in the power cord.
• USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition.
If your product is equipped with a cordset, use only 3-wire extension cords that have
3-prong grounding-type plugs and 3-pole receptacles that accept the tool's plug. When
using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. The following table shows the correct size to use depending on
cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.
Minimum Gauge for Cord Sets
Volts
Total Length of Cord in Feet (meters)
Ampere Rating
120V
25 (7.6)
50 (15.2)
100 (30.5)
150 (45.7)
240V
50 (15.2)
100 (30.5)
200 (61.0)
300 (91.4)
More
Than
0
6
10
12
Not More
Than
6
10
12
16
18
18
16
14
AWG
16
16
16
12
16
14
14
12
14
12
Not Recommended

Publicidad

loading