Ryobi RLS1351 Manual Del Operador página 12

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

TO iNSTALL / REPLACE ThE BLADE
See Figures 11 - 12, pages 19 - 20.
wARNiNg:
A 5 in. blade is the maximum blade capacity of the
saw. Never use a blade that is too thick. Larger blades
will come in contact with the blade guard, while thicker
blades will prevent the blade bolt from securing the blade.
Either of these situations could result in a serious accident
and can cause serious personal injury.
NOTE: The saw blade is removed from beneath the saw base
by passing the blade through the throat plate. If the saw is
mounted to a work bench, it will be necessary to remove
the saw to install/replace the blade.
 Unplug the saw.
 Raise the blade guard by turning the blade guard adjust-
ment knob counterclockwise.
 Loosen screw on blade bolt cover.
 Rotate blade bolt cover up and back to expose the blade
bolt.
 Depress the spindle lock button and rotate the blade
bolt until the spindle locks.
 Using the blade wrench provided, loosen and remove
the blade bolt.
NOTE: The blade bolt has right hand threads. Turn blade
bolt counterclockwise to loosen.
 Remove the outer blade washer. Do not remove the
inner blade washer.
 Lift the side legs of the saw and carefully slip the blade
through the throat plate removing the blade from under
the saw base.
 Wipe a drop of oil onto inner blade washer and outer
blade washer where they contact the blade.
wARNiNg:
If the inner blade washer has been removed, replace it
before placing blade on saw. Failure to do so could cause
an accident since blade will not tighten properly.
 Fit saw blade inside blade guard and onto spindle. The
blade teeth point upward as shown in figure 12.
NOTE: Kerf must be a minimum of 3/32 in.
ASSEMBLy
 Replace the outer blade washer. Double "D" flats on
blade washers align with flats on spindle.
 Depress spindle lock button and replace blade bolt.
CAUTiON:
Always install the blade with the blade teeth and the
arrow printed on the side of the blade pointing up at the
front of the saw.
 Tighten blade bolt securely.
NOTE: The blade bolt has right hand threads. Turn blade
bolt clockwise to tighten.
 Replace blade bolt cover and screw.
 Tighten screw securely.
 Lower the blade guard by turning the blade guard
adjustment knob clockwise until the clearance of the
blade guard from the saw table is between 1/16 in. -
3/32 in.
TO STORE ACCESSORiES
See Figure 13, page 20.
The saw has a convenient storage area specifically designed
for the push stick (on the back of the saw table) and the
blade wrench (under the saw table).
To store the push stick:
 Place the large holes in the key hole slot on the push
stick over the screws.
NOTE: Large holes should be on the bottom.
 Place the push stick firmly against the saw and push the
stick down toward the floor.
NOTE: When stored properly, the push stick will be
below the saw table.
To store the blade wrench:
 With saw unplugged, tilt the saw table back.
 Push the blade wrench into the storage slot on the foot/
blade wrench holder.
TO MOVE ThE SAw
See Figure 14, page 20.
When transporting the saw, always lock the saw to prevent
the saw arm from moving on the sliding rails.
 Unplug the saw.
 Push or pull the saw on the sliding rails until the lock pin
and hole in the rail are aligned.
 Push the lock pin in the hole to lock the saw in place.
 Store the cord by wrapping it around the cord wrap.
 Lift the saw by the carrying handle to transport.
12

Publicidad

Tabla de contenido
loading

Tabla de contenido