Colour Floodlight And Stroboscope; Dmx Connection - IMG STAGELINE RGBL-222DMX Manual De Instrucciones

6) To change the program speed or the flash rate:
GB
a) When the display is not activated, press one
of the control buttons A or B.
b) Press both control buttons A and B at the
same time so that the display starts flashing.
c) Press the button A once so that the display
shows
and 9.
d) Press both control buttons A and B at the
same time again so that the display stops
flashing.
e) To adjust the speed, press the button A (faster)
or B (slower).

5.1.2 Colour floodlight and stroboscope

In this mode, the panel constantly emits light of an
adjustable colour. In addition, the stroboscope
function is available.
1) When the display (2) is not activated, press one
of the control buttons (3).
2) Press both control buttons A and B at the same
time so that the display starts flashing.
3) Press the button A repeatedly until the display
shows and a number between 00 and 99.
4) Press both control buttons A and B at the same
time again so that the display stops flashing.
5) To set the brightness of the colour red, press the
button A (brighter) or B (darker).
6) Repeat steps 1 to 5 to set the brightness of
the colours green (indication ) and blue (indi-
cation ).
7) To activate/deactivate the stroboscope func-
tion or to change the flash rate:
a) When the display is not activated, press one
of the control buttons A or B.
b) Press both control buttons A and B at the
same time so that the display starts flashing.
c) Press the button A repeatedly until the display
shows
d) Press both control buttons A and B at the
same time again so that the display stops
flashing.
e) To adjust the flash rate, press the button A
(faster) or B (slower). To deactivate the stro-
boscope function, set the value 0.
Note: If you adjust the brightness of the colours, the shade
of colour will also change when the colours are mixed.
Therefore, first adjust the desired brightness of the domi-
nating colour, then add the other two colours. To get white,
first set the brightness of green; it is the brightest colour to
the human eye. Then add red to get yellow, and finally add
blue to get white.
10
(Speed) and a number between 1
and a number between 0 and 9.
5.2 Interconnecting several
RGBL-222DMX panels
Several RGBL-222DMX panels can be intercon-
nected (master / slave mode). Thus, the master unit
is able to synchronize all slave units.
1) Interconnect the units in each case via the inline
jack of the cable DMX OUT (5) and the plug (10)
of the cable DMX IN to create a chain. See chap-
ter 5.3.1 "DMX connection", however, skip step 1.
2) The first light effect panel in the chain (of which
the cable DMX IN has not been connected) is
used as a master unit to control the slave units.
Set the slave units to the slave mode:
a) When the display (2) is not activated, press
one of the control buttons (3).
b) Press both control buttons A and B at the
same time so that the display starts flashing.
c) Press the button A or B repeatedly until the
display shows
d) To confirm the setting, press both control but-
tons A and B at the same time. The display
stops flashing.
5.3 Operation with a DMX light controller
For operation via a DMX light controller (e. g. DMX-
1440 or DMX-510USB from "img Stage Line"), the
light effect panel is equipped with 6 DMX control
channels. For the functions of the channels and the
DMX values see chapter 5.3.3.
DMX is the abbreviation of digital multiplex and means
digital control of several DMX units via a common control
cable.

5.3.1 DMX connection

For DMX connection, 3-pole XLR connectors with
the following pin configuration are provided:
pin 1 = ground, 2 = DMX-, 3 = DMX+
For connection, special cables for high data flow
are recommended. Standard microphone cables
with screening and a minimum cross section of 2 ×
0,22 mm 2 and with a capacity as low as possible
can only be recommended for a total cable length
of up to 100 m. For cable lengths exceeding 150 m,
it is generally recommended to insert a DMX level
matching amplifier (e. g. SR-103DMX from "img
Stage Line").
1) Connect the plug (10) of the cable DMX IN to the
inline jack of the supplied cable with XLR plug
(8). Secure the connector with the cap nut. Con-
nect the XLR plug via an extension cable to the
DMX output of the light controller or, if further
DMX-controlled units are used, to the DMX out-
put of the last DMX-controlled unit of the DMX
signal cable.
.