Power Supply; Setting Into Operation; Locking/Unlocking The Unit - Monacor JTS PT-950B Manual De Instrucciones

4 Power supply

G
Insert only batteries of the same type and always
replace all batteries.
G
If the unit is not used for a longer period (e. g. more
than a week), remove the batteries. Thus, the unit
will not be damaged in case of battery leakage.
1) Press down the two latching buttons (8) on the
sides of the transmitter. The control part will unlock
and can be displaced in its casing. Slide the control
part downwards until it locks into place again. This
will allow access to the battery compartment (11)
on the rear side (see fig. 3).
2) Insert two 1.5 V batteries of size AA (R6) into the
battery compartment, with the positive and nega-
tive connections as indicated in the compartment.
3) Unlock the control part, slide it back to its previous
position until it locks into place.

5 Setting into Operation

1) Connect the supplied Lavalier microphone CM-501
to the 4-pole mini XLR jack INPUT (4) and fix it with
the clip to your clothes (e. g. tie or lapel).
Instead of the Lavalier microphone it is also pos-
sible to use a matching headband or instrument
microphone (e. g. CM-204..., CX-504, CX-508W, or
CX-516W from JTS).
2) To switch on, set the power switch (2) to ON. The
display (3) indicates the transmitting frequency
adjusted and a battery symbol which shows the cur-
rent charging status of the batteries in several
steps:
fully charged
3) Press down the latching buttons (8) on the sides of
the transmitter and slide the control part upwards in
its casing until it locks into place (see fig. 1).
4) To adjust the radio frequency for the transmitter
→ see chapter 5.1. Switch on the receiver and set it
to the same frequency → see operating instructions
of the receiver.
Switch on the audio unit (mixer or amplifier)
connected to the receiver.
5) Speak/sing into the microphone. The volume level
can be readjusted by changing the sensitivity via
the control GAIN (10). Use the supplied adjusting
key for turning the control.
Adjust the transmitter to an optimum level. If the
level is too high, the transmitter will distort, in this
case turn back the control (if required, even to the
left stop). If the level is too low, a poor signal-noise
ratio will result, in this case, advance the control
correspondingly.
6) The transmitter can be locked to prevent accidental
change of frequency and accidental switching off
→ chapter 5.2.
8
7) After all adjustments have been made, unlock the
8) Use the clip (9) to attach the transmitter to your
9) To switch off the transmitter after operation, set the
5.1 Adjusting of the transmitting frequency
1) Keep the key SET (7) pressed for 2 s. The display
2) Adjust the frequency with the cursor keys: each
3) Press the key SET to memorize the adjustment.
Note: When using several wireless systems at the
same time, the radio frequencies of the individual
systems should be carefully matched to each other to
prevent interference. Examples for frequencies for
exhausted
simultaneous operation of several systems can be
found in the Internet on www.jts-germany.de under
"Informationen/Intermodulationsfreies Frequenzsetup".

5.2 Locking/unlocking the unit

With the unit locked, it is not possible
a to switch off the unit; if the power switch (2) is set to
b to change the transmitting frequency.
5.2.1 Activating the lock function
1) First recall the frequency adjusting mode: Keep the
2) As soon as the indication MHZ flashes in the dis-
3) Press the key
4) Memorize the adjustment by pressing the key SET.
control part, slide it back to its previous position
until it locks into place.
cloth ing, e. g. belt or waistband.
To modify the position of the transmitter on your
clothing, the clip can also be mounted in a different
way: Unscrew the clip, turn it (clockwise or counter-
clockwise by 90° or by 180°), then retighten it.
power switch (2) to OFF. The display shortly indi -
cates and then extinguishes completely.
shortly indicates
vious indication. The indication MHZ flashes in the
display.
Note: To exit the adjusting mode without making
an adjustment, press the key SET so many times
until the display shows
returns to normal operation.
time the key (6) is pressed, it decreases by
125 kHz, each time the key
increases by 125 kHz.
The display shortly indicates
mode is exited, the unit returns to normal operation.
OFF with the unit locked, the display shows
key SET (7) pressed for 2 s.
play, shortly press the key SET to change into the
lock mode: flashes in the display (locking
deactivated).
(5):
is shortly displayed, the adjusting mode is
exited, the unit returns to normal operation.
and then returns to its pre-
. Then the unit
(5) is pressed, it
, the adjusting
flashes in the display.
.