Power Supply - Monacor JTS IN-64TH/2 Manual De Instrucciones

The regulations of the country where this unit is oper-
ated must always be observed. These regulations can
be found via links to the national authorities from the
following Internet address: www.ero.dk

4 Power Supply

Unscrew the cap (3) of the battery compartment (5).
Insert two batteries of size AA with the positive and
negative poles as imprinted in the compartment. Then
screw on the cap.
5 Operation
1) Before switching on the transmitter, set the receiver
IN-64R/ 2 to an interference-free transmission fre-
quency instruction manual of the receiver.
2) To switch on the transmitter, press the button
After shortly showing the identification number
( chapter 5.1.4), the display (2) will indicate the
number of the channel adjusted, the letter of the
corresponding channel group and a battery symbol
showing the current charging status of the batteries
in several steps:
full
After switching on, the display will be illuminated in
green. The illumination will be extinguished after
10 seconds if no further button is pressed on the
transmitter.
3) Via the REMOSET function, the transmitter can be
automatically set to the transmission frequency of
the receiver. For correct operation, make sure that
→ the REMOSET function on the transmitter is not
deactivated
chapter 5.1.3
→ the transmitter is not set to a different identifica-
tion number than the receiver
chapter 5.1.4
→ the transmitter is not locked
chapter 5.1.5
→ the transmitter is not too far away from the
receiver (maximum range of REMOSET trans-
mission: 10 m)
Check the adjustments on the transmitter and cor-
rect them, if necessary. Then activate the REMO -
SET function on the receiver
of the receiver. During the REMOSET transmission,
the display of the transmitter will show
the transmitter will be set to the channel and the
channel group of the receiver.
It will also be possible to adjust the channel
group and the channel on the transmitter manually
chapter 5.1.1.
(4).
low
instruction manual
, then
4) Speak/sing into the microphone. The volume level
of the microphone will be indicated on the display of
the receiver. It can be readjusted by changing the
sensitivity chapter 5.1.2.
5) The transmitter can be muted (= no signal trans-
mission) for short interruptions. To activate the mut-
ing, press the button
minated in red. The illumination will start flashing
after 10 seconds.
To deactivate the muting, press the button
once again. The illumination of the display will
change to green. It will be extinguished after 10 sec -
onds if no further button is pressed.
6) The transmitter can be locked to prevent accidental
modification of the transmission frequency or
switching off chapter 5.1.5.
7) To switch off the transmitter, keep the button
pressed until is inserted on the display. Then
the transmitter is switched off.
5.1 Adjusting the transmitter
When the transmitter is not locked, the adjusting modes
can be called successively with the button SET (6):
group → channel → sensitivity → REMOSET transmis-
sion → identification number → lock function.
To make adjustments in an adjusting mode, see the
corresponding chapters 5.1.1 to 5.1.5.
5.1.1 Transmission frequency (group and channel)
The REMOSET function can be used to set the trans-
mitter quickly and easily to the transmission frequency
of the receiver ( chapter 5, step 3). However, the
transmission frequency of the transmitter can also be
adjusted manually by selecting the channel group and
the channel. The unit offers 64 preset channels
assigned to four channel groups ( , , , ) [16 chan-
nels per group] table in chapter 7.1.
1) Keep the button SET (6) pressed for approx. 2 sec -
onds until the display shortly shows
the group indication , , or will flash. The group
adjusting mode will be activated.
Note: To exit the adjusting mode without making an
adjustment, press the button SET repeatedly until the
display shows . The unit will then return to normal
operation.
2) Select the group with the button „up"
button „down" (8).
3) Confirm the selection with the button SET. The
channel indication will flash on the display. The
channel adjusting mode will be activated.
4) Select the channel with the button „up"
button „down" (8).
5) Confirm the selection with the button SET.
will be shortly displayed and the unit will go to nor-
mal operation.
®
(4). The display will be illu-
. Then
(7) or the
(7) or the
(4)
9