Switching On/Off The Transmitter; Settings Via The Menu; Basic Settings - Monacor JTS UF-10TB/12 Manual De Instrucciones

4.3 Switching on /off the transmitter
1) Switch on the transmitter with the button
The backlight of the display (11) lights up for a
few seconds. When you press a button (4, 9,
10), the backlight is switched on again.
2) The display shows the following information:
the name of the unit, (10 characters), any name
may be selected (e. g. UF-10TB as shown in
fig. 1)
G = the group number (1 ...12)
C = the channel number (1 ... 60)
MHz = the transmission frequency
(624.000 ... 694.000 MHz)
. . dB = the microphone sensitivity adjusted
(-18 dB ... 12 dB)
the battery status:
full
3) To switch off, keep the button
2 seconds until the display shows

4.4 Settings via the menu

All settings are made via a menu:
1) To call up the main menu (fig. 2), keep the but-
ton SET (10) pressed for two seconds until the
menu appears on the display (11).
2) Press the button ▼ or ▲ (9) to select the
desired menu item. Then call up the menu item
with the button SET.
3) To make the setting, press the button ▼ or ▲.
4) If several setup functions are available for a
menu item (e. g. group number and channel
number), press the button SET to go from one
function to the next one.
5) To save a setting, press the button SET. The dis-
play briefly shows
menu reappears.
To exit a menu item without a change, press
the button
6) To exit the main menu, press the button
press the button ▼ or ▲ to select the menu item
Exit
and then press the button SET.
All setting options via the menu can be found in the
following chapters.
12
discharged
Power OFF
Saving...
before the main
(4). The main menu reappears.

4.5 Basic settings

(4).
1) If it is difficult to read the display (11), call up the
contrast setting via the menu item
a) Keep the button SET (10) pressed for two
seconds until the main menu (fig. 2) ap -
pears.
b) Press the button ▼ or ▲ (9) to select the
menu item
ton SET.
c) Press the button ▼ or ▲ to set the contrast.
The display shows the value adjusted
(between -3 and 3).
d) Press the button SET to save the setting.
The main menu reappears.
e) To deactivate the main menu, press the but-
ton
pressed for
the corresponding menu item and press the
.
button SET.
2) Set the time for the display backlight via the
menu item
Light Time
15 Sec.
Always OFF
5 - 30 Sec.
Always ON
Hint: To save the batteries, it is advisable not to use
Always ON
3) Via the menu item
entered (10 characters max.) which will appear
on the display (e. g.
fig. 1). When several transmitters are used, this
will make it easier to distinguish between the
transmitters and to identify them. After the menu
item
ter position is selected:
User Name
or
UF-10TB
Char:1/10
Press the button ▼ or ▲ to select the desired
character. Press the button SET to go to the
next character position. After setting the name,
press the button SET repeatedly until the dis-
play shows
pears.
Contrast
. Then press the but-
Contrast
0
Fig. 3
(4) or to change another setting, select
Light T
:
Fig. 4
= no backlight
= time in seconds
= backlight always on
as a final setting.
Name , a unit name can be
UF-10TB
Name
has been called up, the first charac-
Fig. 5
Saving...
. The main menu reap-
Contrast
:
as shown in