Setting The Transmission Frequency; Remoset ® Function - Monacor JTS UF-10TB/12 Manual De Instrucciones

4.6 Setting the transmission frequency

Before switching on the pocket transmitter, set the
receiver to an interference-free frequency (see
instruction manual of the receiver). Then set the
transmitter to the same frequency: There are three
methods to do this:
1. If you operate the pocket transmitter with the
receiver UF-10R /12, the easiest way is to use
the patented REMOSET function. When you
press the button REMOSET on the receiver, the
transmitter is set to the transmission frequency
selected on the receiver (chapter 4.6.1).
2. The transmission frequency can be ad -
justed manually between 624.000 MHz and
694.000 MHz (chapter 4.6.2).
3. For operating several audio transmission sys-
tems at the same time, there are 12 groups with
up to 60 channels in each group (
page 28, 29). In ideal conditions, up to 40 chan-
nels from a group can be used for audio trans-
mission at the same time. If the receiver has
been set to a channel from these groups, select
the same channel for the pocket transmitter
(chapter 4.6.3).
4.6.1 REMOSET ® function
For the REMOSET function always make sure that
1. no menu is called up on the pocket transmitter
or on the receiver.
2. the transmitter is switched on and close to
the receiver (REMOSET transmission range:
approx. 10 m).
3. the transmitter and the receiver are set to the
same identification number (ID No.) or that the
function ID No. is deactivated (see paragraph
"Identification number").
4. the REMOSET function is not disabled (see
paragraph "Disabling the REMOSET
tion").
5. the receiver and the pocket transmitter are not
locked ( chapter 4.9).
6. the LED MUTE (3) does not flash. If it keeps
flashing, the transmitter is muted. In this case,
press the button
guished.
table on
®
(4) so that the LED is extin-
Identification number
To prevent mutual interference of individual pairs of
transmitter / receiver during REMOSET transmis-
sion, each pair must have a different identification
number (ID No.). If you only use one pair of trans-
mitter / receiver, there is no need to change the pre-
set ID No. 0. To change the ID No.:
1) Call up the setting for the ID No. via the menu
Device ID
item
Device ID
0
ID : ON
2) Press the button ▼ or ▲ to set the ID No.
3) Press the button SET. Then press the button ▼
to deactivate the function (OFF) or the button ▲
to activate the function (ON). If the function has
been deactivated, the REMOSET transmission
will be possible from any UF-10R /12 receiver; if
it has been activated, the REMOSET transmis-
sion will only be possible from a receiver with
the same ID No.
4) Press the button SET to save the setting.
REMOSET ® transmission
Press the button REMOSET on the receiver. As
soon as the pocket transmitter has been set to the
transmission frequency or to the group and the
transmission channel of the receiver, the LED
REMOSET (7) shows blue for five seconds.
If the LED REMOSET does not light up, the
automatic synchronization of the transmitter has
failed. In this case, the button REMOSET on the
receiver keeps flashing slowly. For troubleshooting
see steps 1 – 6 at the beginning of this chapter.
Check the settings on the transmitter and possibly
on the receiver and correct them. Then press the
button REMOSET on the receiver again.
func-
Disabling the REMOSET
The REMOSET function can be disabled to prevent
automatic frequency setting.
1) Call up the menu item REMOSET in the main
menu.
Remote Set
ON
OFF
2) Press the button ▼ to disable the function (OFF)
or the button ▲ to enable the funtion (ON).
3) Press the button SET to save the setting.
of the main menu.
Fig. 6
® function
Fig. 7
13