Ordering Spare Parts And Accessories; Disposal And Recycling - EINHELL TE-BD 750 E Manual De Instrucciones

use any harsh, abrasive cleaning solvents.
Ensure that no liquid seeps into the device.
Regrease all bare parts when the work is
finished. The drill pillar, blank parts of the
column, and the drill table especially should
be regreased at regular intervals. Use a stan-
dard, acid-free lubricating grease to do this.
Caution: Do not use your household refuse
bin as a receptacle for oil and grease-soaked
cleaning rags or grease and oil sludge. Dis-
pose of these toxic materials in an environ-
mentally-friendly fashion. Regularly check and
clean the ventilation holes. Store the device
in a dry room. Should the device become
damaged, do not try to repair it yourself; leave
this work to the hands of a qualified electrical
technician.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use cleaning
agents or solvents; these could attack the
plastic parts of the equipment. Ensure that no
water can seep into the device. The ingress of
water into an electric tool increases the risk of
an electric shock.
8.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.2.1 Changing the V-belt (Figs. 31-32)
The V-belt of the pillar drill is a wear part and
should be replaced when worn. Proceed as fol-
lows:
•
Run the machine run in idle mode while slowly
setting the speed adjustor lever (15) to the
minimum speed.
•
Switch the machine off, then pull the power
plug.
•
Set the speed adjustor lever (15) to the maxi-
mum speed setting to slacken the V-belt.
•
Undo the screw (37) to open the V-belt cover
(7).
•
Pry the V-belt (39) off of the drive pulley (38)
by pulling up the belt on one side and slowly
turning the pulley (38). The drive pulley (38)
comprises two disks that are pressed together
via a spring. If the V-belt (39) does not exhibit
enough play to remove it, gently press the
bottom half of the drive pulley (38) down to
slacken the V-belt (39).
•
Fit one end of the new V-belt (39) to the vari-
able pulley (40). Fit the other end to the drive
Anl_TE_BD_750_E_SPK9.indb 28 Anl_TE_BD_750_E_SPK9.indb 28
GB
pulley (38) by first sliding it into the groove on
one side of the pulley (38) , then prying the V-
belt (39) across the pulley into the groove on
the other side.
•
Close the V-belt cover and screw down using
the screw (37).

8.3 Ordering spare parts and accessories

Please provide the following information when
ordering spare parts:
•
Type of unit
•
Article number of the unit
•
ID number of the unit
•
Spare part number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info
Tip! For good results we
recommend high-quality ac-
cessories from
www.kwb.eu
welcome@kwb.eu

9. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should be
taken to a suitable collection center for proper dis-
posal. If you do not know the whereabouts of such
a collection point, you should ask in your local
council offi ces.
- 28 -
!
06.02.2018 10:25:31 06.02.2018 10:25:31