IMG STAGELINE LED-820DMX Manual De Instrucciones página 12

6 Operation without DMX Controller
GB
When there is no DMX control signal at the jack DMX
INPUT (5), the yellow LED MASTER (10) will light up,
the display (7) will show the master mode (indication
) and the unit will automatically change the colour
of the light beam. For this purpose, the Blackout mode
must be deactivated,
For changing the colour of the light beam according
to the beat of the music, activate the music control:
1) Press the button MENU (12) so many times until the
display (7) shows
button is pressed within 8 seconds, otherwise the
adjusting process will end automatically.
2) Activate the menu item
ENTER (14). The display will indicate the operating
status:
= music control activated
= music control deactivated
3) Use the button
the music control and press the button ENTER to
confirm.
4) For music control, adjust the SENSITIVITY control
(3) for the microphone in such a way that the
change of colour will be optimally controlled by the
music. The green LED SOUND (16) will shortly light
up with each control signal created by the sound
picked up with the microphone.
Notes
1. When the volume at the music system is modified, the
microphone sensitivity must be adapted accordingly with
the rotary control.
2. When the volume is too low or when the SENSITIVITY
control is set to the left stop, the unit will automatically
change between two colours.
6.1 Interconnecting several LED-820DMX units
Several LED-820DMX units may be interconnected in
order to control all slave units in sync with the master
unit.
1) Connect the DMX OUTPUT (6) of the master unit
via a 3-pole XLR cable (e. g. series MEC-... or
MECN-... from the product range of "img Stage
Line") to the DMX INPUT (5) of the first slave unit.
2) Connect the DMX OUTPUT of the first slave unit to
the DMX INPUT of the second slave unit, etc. until
all units have been connected in a chain.
3) Set the slave units to one of the slave modes:
a) Press the button MENU (12) so many times until
the display (7) shows
next button is pressed within 8 seconds, other-
wise the adjusting process will end automati-
cally.
12
chapter 5.1.
. Make sure that the next
with the button
or (13) to activate or deactivate
. Make sure that the
b) Activate the menu item
ENTER (14). The display will indicate the slave
mode adjusted:
Slave mode 1: The slave unit will be con-
trolled in sync with the master unit.
Slave mode 2: The slave unit will be con-
trolled opposite to the master unit.
Slave modes 3 and 4: Control variants
for the slave units when 3, 4 or more
units of the type LED-820DMX are used.
c) Use the button
slave mode and press the button ENTER to con-
firm.
Once the control signals from the master unit are
applied to the slave units, the red LED SLAVE (15)
will light up on the slave units.
6.2 Remote control LC-3
The remote control LC-3 available as an accessory
allows to control various functions.
1) Connect the remote control to the jack ONLY FOR
REMOTE CONTROL (4).
2) There must be no DMX signal at the DMX INPUT
(5).
3) Via the DMX OUTPUT (6), further LED-820DMX
units may be connected (
control them together with the master unit via the
remote control.
4) With the button STAND BY (17), the light beam can
be activated or deactivated. When the light beam is
deactivated, the LED next to the button STAND BY
will light up as a check.
5) Select the operating mode with the button MODE
(19):
a) When the LED of the button MODE is off, the
stroboscope mode will be activated. By keeping
the button FUNCTION (18) pressed, one of the
three stroboscope functions can be activated:
1. permanent stroboscope
2. stroboscope salvos
(also alternately for the slave units when they
are set to the slave mode 2, 3 or 4,
ter 6.1)
3. music-controlled stroboscope
When the button FUNCTION is kept pressed
again, the next stroboscope function respec-
tively will be activated.
b) When the LED of the button MODE is on, the
colour change mode will be activated. By shortly
pressing the button FUNCTION, the colour of
the light beam can be selected.
with the button
or (13) to select the desired
chapter 6.1) in order to
chap-