Basic Adjustments; Setting The Unit Into Operation - IMG STAGELINE LED-820DMX Manual De Instrucciones

3 Applications
The unit LED-820DMX is designed for lighting applica-
tions on stage, in discotheques or party rooms. It is
ideally suited for illuminating mirror balls. As a light
source, it has a super bright white LED (20 W) with a
low power consumption and a long life. Due to the
colour wheel, eight colours plus white will be available
for the light beam.
The unit is designed for control via a DMX light con-
troller (3 DMX control channels); however, it can also
be operated on its own or with the remote control
LC-3 available as an accessory.
4 Mounting
G
Always place the unit in such a way that a sufficient
air circulation will be ensured during operation.
Never cover the air vents on the housing (e. g. by
curtains).
G
The minimum distance to the illuminated object
should be 10 cm.
1) Screw the light effect unit with the mounting bracket
(1) to a suitable place, e. g. on a cross bar or a light-
ing stand.
WARNING Mount the light effect unit safely and
expertly. If it is installed at a place
where people may walk or sit under
it, additionally secure it (e. g. by a
safety rope; fasten the safety rope in
such a way that, even in the event of
a fall, the maximum falling distance
of the unit will not exceed 20 cm).
2) To align the light effect unit, release the locking
screws (2). Adjust the desired inclination of the unit,
then retighten the screws.

5 Setting the Unit into Operation

WARNING Never look directly into the light beam;
this may cause eye damage.
Please note that fast changes in light-
ing, e. g. flashing light, may trigger
epileptic seizures with photosensitive
persons or persons with epilepsy!
Connect the mains cable provided to the mains jack (8)
first, then connect it to a socket (230 V~/ 50 Hz). During
the starting phase, the display (7) will indicate
Then the unit will be ready for operation and can be
controlled via a DMX controller (
automatically change the colour of the light beam in
the master mode ( chapter 6). To switch off the unit,
disconnect the mains plug.
For a more convenient operation, it is recom-
mended to connect the unit to a mains socket which is
switched on and off via a light switch.
Caution: Do not connect the unit to the mains voltage
via a dimmer!
.
chapter 7) or will

5.1 Basic adjustments

When the light beam is directed at an even surface,
e. g. a wall, the light cone can be focussed by turning
the lens.
The following basic adjustments can be made via
the display (7) and the control buttons (12 – 14). For
this purpose, press the button MENU (12) so many
times until the desired function is displayed. Then
press the button ENTER (14). Make sure that the next
button is pressed within 8 seconds, otherwise the
adjusting process will end automatically. The menu
structure can be found on page 15.
Blackout mode off or on
Use the button or (13) to select:
The light beam will be permanently activated.
This adjustment must be selected when the
unit is operated without a DMX controller.
The light beam will only be activated when
there is a DMX control signal at the jack
DMX INPUT (5). Once the DMX controller is
switched off, the light beam will be deactivated.
To memorize, press the button ENTER (14).
Display on or off
Use the button or (13) to select:
The display (7) will always be on.
The display will be switched off approx. 60 s
after pressing the last button. It will be switched
on again the next time a button is pressed.
To memorize, press the button ENTER (14).
Display representation
Use the button ENTER (14) to select and memorize at
the same time:
normal representation
representation turned by 180°
Approx. 8 s after pressing the last button, the adjusting
menu will be exited automatically.
GB
11